- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
Steel guide 6.2 x 10 mm
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Reference: 33/27
Rotor blade tie-down large
The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...
Reference: 340/7
Fuselage centre section for Lama
Component part for fuselage Lama, Ord.No. 3300, 3400, and 3401.
Reference: 97/9
Screw fitting pushrod connector
Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...
Reference: 33/28
Rotor blade tie-down
Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...
Reference: 791/28
Wing brace
The wing brace prevents the wings vibrating; it can be installed in the Cobra, depending on model version.
Reference: 18/10
PTFE tube for tail drive shaft
PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm
Reference: 3947
Quick-release servo mount
During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...
Reference: 3936/1
Y-lead
If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.
Reference: 603/16
Tail boom set, Schweizer 300 C
Component part for fuselages, Ord.No. 6030 or 6031.