- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
O-ring 3 x 8 mm hard
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Référence: 33/22
Rotor blade support
If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...
Référence: 10/1
Dispenser for UHU plus endfest 300
Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.
Référence: 97/9
Screw fitting pushrod connector
Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...
Référence: 3936/1
Y-lead
If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.
Référence: 8/3
Tail rotor flange
The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...
Référence: 18/11
Aluminium tube 5.5 x 4.4 x 1000 mm
Aluminium tube 5.5 x 4.4 x 1000 mm
Référence: 333/5
Rotor blade pouch 5-blade Ø 2500 mm
bag length: 120 cmmax. blade width: 9.5 cm
Référence: 3948
Servo numbers
Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30
Référence: 330/10
Housse de protection pour Lama
This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400
Référence: 330/18
Gear support for tail drive
Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3
Référence: 18/10
PTFE tube for tail drive shaft
PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm
Référence: 603/19
Adaptor, tail boom rear, GRP
Component part for fuselages, Ord.No. 6030 or 6031.
Référence: 3944
Servo mount 120°
When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...
Référence: 33/25
Porte pales pour transport
La bonne solution pour le transport: La découpe du grand support convient aux différentes formes des poutres sur les fuselages.Support de transportpour fuselages, 30 x 270 x 200 mm