Tail cap Bell 230

Reference: 68/1

Swivel bearing 10 x 19 x 9 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 10 x 19 x 9 mmpack of 1

Reference: 117/2

Thrust bearing 10 x 24 x 9 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 10 x 24 x 9...

Reference: 17/23

7 x 14 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 7 x 14 x 3.5 mmpack of...

Reference: 64/19

15 x 24 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 15 x 24 x 5 mmpack of...

Reference: 40

4 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 4 x 13 x 5 mmpack of...

Reference: 116/94

Silencer for 116/95

Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm

Reference: 94/3

Thrust bearing 4 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 4 x 10 x 3...

Reference: 870/49

Servo frame CFK

Reference: 117/1

Thrust bearing 9 x 20 x 7 mm

Not available

Reference: 11/62

Crankshaft nut socket spanner 13 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 13 mm, for Rossi or Webra

Reference: 4309

Rossi glowplug, extra-cold

hot engine - cold plug (Summer) cold engine - hot plug (Winter)

Reference: 111/30

Slot head set

The kit contains: Ord.No. 11/51      PH0, PH1 Ord.No. 11/52      SW 2,5 / 4,0 Ord.No. 111/31    SW 2,0 / 3,5 Ord.No. 111/32    PH000, PH00 Ord.No. 111/33    PZ0, PZ1

Reference: 94/6

Thrust bearing 6 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 6 x 10 x 3...

Reference: 40/1

4 x 9 x 4 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 4 x 9 x 4 mmpack of...

Reference: 870/53

Bearing plate, GFK

Not available

Reference: 94/17

Thrust bearing 7 x 13 x 4.5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...