Accueil

Filtrer par

Motorisation

Motorisation

Disponibilité

Disponibilité

Poids

Poids

  • 0Kg - 10Kg

Prix

Prix

  • 0,00 € - 18 400,00 €

langage

langage

Type de rotor

Type de rotor

Motorization

Motorization

Catégories

Catégories

Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 4186 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 1537-1548 de 4186 article(s)

Filtres actifs

  • Disponibilité : En stock
Swashplate driver for rotor... Aperçu rapide

Référence: 68/20-5

Swashplate driver for rotor head 705/30

Commentaire(s): 0

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Prix 87,20 €
Détails
En vente sur demande
Control electronics Aperçu rapide

Référence: 3175

Control electronics

Commentaire(s): 0

Making up the wiring loom for extending machine guns, including the ON / OFF switch, can be very time-consuming even when you have a wiring diagram to follow.The alternative is this module, which simplifies matters considerably as it contains all the electronic circuitry required to control the system.The electronic control circuit can be used with any...

Prix 65,70 €
Détails
En vente sur demande
Tuned pipe holder X-Treme Aperçu rapide

Référence: 310/25

Tuned pipe holder X-Treme

Commentaire(s): 0

Engines with rear exhaust enable the installation of the tuned pipe underneath the mechanics of a trainer helicopter, mounted at the mechanics.Depending on the kind of the engine the sizes of the tuned pipes vary in size. The difference of these sets is due to the diameter of the fastening clamp.Tuned pipe holderset suitable for tuned pipe 116/33

Prix 34,30 €
Détails
En vente sur demande
Tap M 3.0 HSS Aperçu rapide

Référence: 11/78

Tap M 3.0 HSS

Commentaire(s): 0

Good thread-cutting oil is as important as the tap, as it extends the useful life of the tool several times over.

Prix 28,10 €
Détails
En vente sur demande
Blade holder screw M 4 G12 Aperçu rapide

Référence: 052

Blade holder screw M 4 G12

Commentaire(s): 0

Pack of 2 with self-locking nuts M 4Tip: To avoid losing those blade holder screws - push them straight back into the blade holders and fit the nuts loosely, than you know where they are next time when you assemble the model.

Prix 6,60 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook