Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 145 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 61-72 su 145 articoli

Filtri attivi

Motor mount for Webra 8 cc Anteprima

Riferimento: 59/5

Motor mount for Webra 8 cc

Recensioni: 0

Factory-drilled motor mounts, already drilled and tapped for M 3 or M 4, are available in pairs (left / right). Avoid interchanging the left hand with the right hand one!1 pairfactory-drilled

Prezzo 37,50 €
Più
In vendita su richiesta
Tuned pipe holder for... Anteprima

Riferimento: 310/2

Tuned pipe holder for fuselages

Recensioni: 0

The shape of a fuselage is not always correct to support the tuned pipe at the exit (e.g. model Tiger).Tuned pipe holder for fuselagesset suitable for tuned pipe 116/16

Prezzo 34,30 €
Più
In vendita su richiesta
Charger for 12 V starter... Anteprima

Riferimento: 3491

Charger for 12 V starter battery

Recensioni: 0

Use this battery charger to recharge the starter battery; mains connection for 230 V. Charger for 12 V starter battery

Prezzo 54,60 €
Più
In vendita su richiesta
lining 45 x 40 x 12 mm Anteprima

Riferimento: 64/8

lining 45 x 40 x 12 mm

Recensioni: 0

Friction between the flywheel and the clutch bell result in a certain amount of wear of the clutch lining.For installation you slightly grind one of the outer edges. Afterwards you press the liner with that edge in front into the clutch bell. To glue in a new clutch liner you use e.g. UHU plus endfest 300, Ord.No. 10/26 or 10/27.Fits the glow plug motor...

Prezzo 27,40 €
Più
In vendita su richiesta
Tuned pipe silencer Anteprima

Riferimento: 116/71

Tuned pipe silencer

Recensioni: 0

 Tuned pipe silenceroverall length 400 mmconnection-Ø 20 mmoverall Ø 40 mmsilencer chamber 240 mmweight approx. 180 gtail pipe length 100 mm

Prezzo 176,40 €
Più
In vendita su richiesta
Teflon Tubo 20x2, 5x120mm Anteprima

Riferimento: 115/5

Teflon Tubo 20x2, 5x120mm

Recensioni: 0

Manifolds and tuned pipes or silencers must be installed without touching each other, because the contact of these metal parts could cause radio interference. We can refer to this interference as "electric noise". The connection by PTFE pipe enables the required distance of 10 - 15 mm in the prescribed position, and it steadily seals gas-tight. This...

Prezzo 19,40 €
Più
In vendita su richiesta
Tuned pipe holder X-Treme Anteprima

Riferimento: 310/25

Tuned pipe holder X-Treme

Recensioni: 0

Engines with rear exhaust enable the installation of the tuned pipe underneath the mechanics of a trainer helicopter, mounted at the mechanics.Depending on the kind of the engine the sizes of the tuned pipes vary in size. The difference of these sets is due to the diameter of the fastening clamp.Tuned pipe holderset suitable for tuned pipe 116/33

Prezzo 34,30 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook