Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Collective pitch compensator 12 mm

722/71
Valutazione 

Pitch compensator, complete, for 12 mm Ø main shaft, centre piece aluminium.
For use with the rotor head Ord.No. 722/72.

169,20 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

Pitch compensator, complete, for 12 mm Ø main shaft, centre piece aluminium.
For use with the rotor head Ord.No. 722/72.

Dettagli del prodotto
722/71
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Collective pitch compensator 12 mm

Collective pitch compensator 12 mm

Pitch compensator, complete, for 12 mm Ø main shaft, centre piece aluminium.
For use with the rotor head Ord.No. 722/72.

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Rotor head dampers for 2... Anteprima

Riferimento: 74/7

Rotor head dampers for 2 blade FBL systems

Recensioni: 0

Flybarless electronics have now become common. Where they are being used harder damping is required.For these cases Vario is now offering a harder damping of the blade shaft provided by a pretension absorbing element in the centre block.For the adjustment, the outer O-ring position can be selected between "hard" and "soft" flight characteristics.Important...

Prezzo 30,60 €
Più
In vendita su richiesta
Rotor brake, GRP Anteprima

Riferimento: 72/4

Rotor brake, GRP

Recensioni: 0

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...

Prezzo 14,70 €
Più
In vendita su richiesta
Aluminium side frames Anteprima

Riferimento: 68/22

Aluminium side frames

Recensioni: 0

Aluminium side frames for swashplate driver 68/20 and 68/50. Content of the package: 2 pieces

Prezzo 30,60 €
Più
In vendita su richiesta
Set leva miscelatore Anteprima

Riferimento: 78/40

Set leva miscelatore

Recensioni: 0

Mixer levers are an essential part of every flybar-controlled rotor head. From the swashplate a pushrod runs to the ballraced mixer arm which is screwed to the blade holder arm. The mixer levers transmit the control movement to the flybar via the double ball-link.Additionial accessories for the use of mixer levers are either two flanged ballraces or two...

Prezzo 37,50 €
Più
In vendita su richiesta
O-ring 2 x 19 mm soft Anteprima

Riferimento: 74/18

O-ring 2 x 19 mm soft

Recensioni: 0

O-ring 2 x 19 mm soft Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prezzo 6,30 €
Più
In vendita su richiesta
O-ring 2 x 6 mm soft Anteprima

Riferimento: 74/6

O-ring 2 x 6 mm soft

Recensioni: 0

O-ring 2 x 6 mm soft Content of the package: 8 piecesTip: O-rings always slide with a drop of silicone oil onto the shaft.

Prezzo 6,30 €
Più
In vendita su richiesta
GRP blade holder, 5 mm ∅ hole Anteprima

Riferimento: 76/19

GRP blade holder, 5 mm ∅ hole

Recensioni: 0

As demands on helicopters continue to rise, so stronger blade holders are required. In this case a 14 mm blade holder is combined with a 5 mm Ø hole for blade retention, i.e. the matching blade holder screws and self-locking nuts are M5 in size.GRP blade holder with short linkage armfor multi-blade rotor heads

Prezzo 30,60 €
Più
In vendita su richiesta
Inertia weights for Ø 5 mm... Anteprima

Riferimento: 79/8

Inertia weights for Ø 5 mm flybar

Recensioni: 0

Inertia weights are small "extra brakes". They increase the gyroscopic stability of the flybar and slow down the rotor head's response. For every beginner we recommend these so the responsiveness of the rotor head is reduced. The rotor head becomes more responsive as the inertia weights are moveded inwards (always place equally!). Inertia weights suitable...

Prezzo 30,60 €
Più
In vendita su richiesta
Shaft bearing Anteprima

Riferimento: 72/32

Shaft bearing

Recensioni: 0

Shaft bearing Content of the package: 1 piece

Prezzo 17,00 €
Più
In vendita su richiesta
Flybar stainless steel 4 x... Anteprima

Riferimento: 79

Flybar stainless steel 4 x 450 mm

Recensioni: 0

The length of the flybar itself also plays an important role in the model's flight characteristics: the longer the flybar, the smoother the hover. A longer flybar increases the control deflections. 450 mm length is considered normal, while 510 mm provides more docile handling.

Prezzo 17,00 €
Più
In vendita su richiesta
Paddles 3-D Anteprima

Riferimento: 91/65

Paddles 3-D

Recensioni: 0

 Paddles1 pairapprox. 19 g eachfor 4 mm Ø flybar

Prezzo 27,40 €
Più
In vendita su richiesta

Seguici su Facebook