Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Bellcrank set 60 degree

61/20
Valutazione 



The ballraced 60° bellcrank, for example, is positioned between the horizontal pushrod from the throttle servo and the pushrod running to the barrel arm on the carburettor. When the arm below the ball is vertical the engine is stopped. When the 60° arm is horizontal the engine is at full throttle.
In models with overhead tail rotor (e.g. BK 117, BO 105) this bellcrank can be applied for the tail rotor control.

32,30 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione



The ballraced 60° bellcrank, for example, is positioned between the horizontal pushrod from the throttle servo and the pushrod running to the barrel arm on the carburettor. When the arm below the ball is vertical the engine is stopped. When the 60° arm is horizontal the engine is at full throttle.
In models with overhead tail rotor (e.g. BK 117, BO 105) this bellcrank can be applied for the tail rotor control.

Dettagli del prodotto
61/20
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Bellcrank set 60 degree

Bellcrank set 60 degree



The ballraced 60° bellcrank, for example, is positioned between the horizontal pushrod from the throttle servo and the pushrod running to the barrel arm on the carburettor. When the arm below the ball is vertical the engine is stopped. When the 60° arm is horizontal the engine is at full throttle.
In models with overhead tail rotor (e.g. BK 117, BO 105) this bellcrank can be applied for the tail rotor control.

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Mechanics spacer Anteprima

Riferimento: 830/56

Mechanics spacer

Recensioni: 0

Mechanics spacer al., front. Content of the package: 1 piece.

Prezzo 46,10 €
Più
In vendita su richiesta
Dome plate GRP Anteprima

Riferimento: 53

Dome plate GRP

Recensioni: 0

At the top of the mechanics the dome plate supports the rotor shaft with the help of a 10 x 21 x 5 mm or 12 x 21 x 5 mm ballrace. To reduce the load on the ballrace a thrust bearing can also be fitted under the dome plate.

Prezzo 17,00 €
Più
In vendita su richiesta
Servo mount Anteprima

Riferimento: 907/2

Servo mount

Recensioni: 0

Use this special servo mount for installing the throttle servo on the base plate.

Prezzo 17,00 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook