Cooling fan support for Schweizer 300 C

Référence: 791/28

Wing brace

The wing brace prevents the wings vibrating; it can be installed in the Cobra, depending on model version.

Référence: 8/3

Tail rotor flange

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Référence: 603/16

Tail boom set, Schweizer 300 C

Component part for fuselages, Ord.No. 6030 or 6031.

Référence: 33/66

Rotor blade pouch 2x3 blade max Ø 2500 mm

Référence: 13/21

Magnets for speed regulator

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Référence: 10/46

Capuchon terminal Ø 20 mm

Pack of 2

Référence: 97/4

Servo linkage set

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Référence: 33/3

Rotor blade pouch 3-blade Ø 2500 mm

Référence: 18/10

PTFE tube for tail drive shaft

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Référence: 3947

Quick-release servo mount

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Référence: 18/1

PVC tube 3.0 x 2.0 x 980 mm, red

PVC tube 3.0 x 2.0 x 980 mm, red

Référence: 33/28

Rotor blade tie-down

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Référence: 97/9

Screw fitting pushrod connector

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Référence: 18

PVC tube 3.2 x 2.2 x 1000 mm, white

PVC tube 3.2 x 2.2 x 1000 mm, white

Référence: 33/4

Rotor bolsa de cuchillas 4 cuchillas Ø 2500 mm

Référence: 340/7

Fuselage centre section for Lama

Component part for fuselage Lama, Ord.No. 3300, 3400, and 3401.