Pedales llama x2 1: 4

Riferimento: 350/17

Coperchio scarico Ø 90 mm

When the turbine of a full-size helicopter is not running, the engine is protected with an exhaust cover which prevents foreign objects finding their way inside the turbine. This exhaust cover for model turbines is suitable for the Lama, Alouette III and any other machine with a 90 mm Ø exhaust pipe. Caution: it is essential to allow the exhaust pipes to...

Riferimento: 31/34

Kit cloche con pedali

Incl. programmatore per il nuovo controller del motore lavorato volo mount tempo, Lipo 12S, 5 Ah, ca. 12 minuti, a seconda del pesodel modello.Per l'uso con la...

Riferimento: 341/409

BTP Lama 1: 4

Riferimento: 1/21

Helmet for pilot William

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Riferimento: 341/508

Serbatio olio piccolo Lama 1/4

dimensions: 5.45 x 1.66 x 5.36 cm

Riferimento: 341/36

CESTELLO SOTTOPANCIA PER LAMA

Load basket for Lamalength:410 mmwidth:100 mmheight70 mm

Riferimento: 341/417

Specchio Grande, Lama 1:4

dimensions: 4 x 5.4 x 1 cm

Riferimento: 340/13

Finta trasmissione

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Riferimento: 341/402

Filtro, Lama 1:4

dimensions: 4.3 x 2.5 cm, inner diameter: 1.43 cm

Riferimento: 341/424

Kick bar llama 2 partes 1: 4

Riferimento: 340/5

Snowboards per Lama 1 paio

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Riferimento: 330/2

Imitazione turbina

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Riferimento: 341/404

Luci di posizione Lama 1/4 , 2 pc

dimensions: 4.5 x 3.2 x 1.8 cmPack of 2 (l/r)

Riferimento: 340/6

Pedana di salita per Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Riferimento: 341/411

Llama estabilización trasera 1: 4

Riferimento: 134/410

Antena superior 1: 4