Silencer system

Référence: 35/13

Flanged ballrace 4 x 9 x 4 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Référence: 870/53

Bearing plate, GFK

Not available

Référence: 715/80

Steel manifold for Mizar

 Steel manifold for Mizar with petrol engine34 mm hole spacinge.g. for ZG22 or G230

Référence: 64/71

8 x 14 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 14 x 3.5 mmpack of...

Référence: 68/51

Swivel bearing 12 x 22 x 10 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 12 x 22 x 10 mmpack of 1

Référence: 16/3

Spray can holder

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Référence: 11/22

Magnetiser

Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...

Référence: 116/94

Silencer for 116/95

Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm

Référence: 4302

Bougie Enya 6

Contenu du paquet 1 piècemoteur chaud - bougie froide (été) moteur froid - bougie chaude (hiver)

Référence: 94/17

Thrust bearing 7 x 13 x 4.5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...

Référence: 11/67

Crankshaft nut socket spanner 14 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Référence: 870/49

Servo frame CFK

Référence: 55/8

12 x 28 x 8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 12 x 28 x 8 mmpack of...

Référence: 68/2

20 x 32 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 20 x 32 x 7 mmpack of 1 

Référence: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Référence: 117/1

Thrust bearing 9 x 20 x 7 mm

Not available