- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
Rotor blade tie-down
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Référence: 3942
Servo packer
Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10
Référence: 333/5
Rotor blade pouch 5-blade Ø 2500 mm
bag length: 120 cmmax. blade width: 9.5 cm
Référence: 33/22
Rotor blade support
If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...
Référence: 74
O-ring 3 x 8 mm hard
O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.
Référence: 18/10
PTFE tube for tail drive shaft
PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm
Référence: 10/75
Glue dispenser
When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.
Référence: 340/7
Fuselage centre section for Lama
Component part for fuselage Lama, Ord.No. 3300, 3400, and 3401.
Référence: 33/2
Rotor blade pouch 2-blade Ø 2100 mm
bag length: 98 cmmax. blade width: 9.5 cm
Référence: 3947
Quick-release servo mount
During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...
Référence: 97/4
Servo linkage set
When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...