Horizontal stabiliser GRP Flash

Reference: 71/19

2.5 x 8 x 2.8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 2.5 x 8 x 2.8 mmpack of...

Reference: 116/8

Silicone hose

The operating temperature of a tuned pipe or of a silencer has a destructive influence on their supports, if no heat resitant material is used when fixing.Silicone hose11 mm I.D.length approx. 300 mm

Reference: 10/73

Five minute epoxy, 50 ml

The more you build, the more frequently you use epoxies, whose components must be proportionately mixed. When you insert cartridges into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use. Pack of 50 ml, pot life approx. 5 minutes

Reference: 58/11

3 x 8 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 8 x 3 mmpack of...

Reference: 870/53

Bearing plate, GFK

Not available

Reference: 830/42

Exhaust mount 42 mm

  For silencer Ord.No. 116/96.Content of the package1 piece

Reference: 870/49

Servo frame CFK

Reference: 94/3

Thrust bearing 4 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 4 x 10 x 3...

Reference: 55/1

10 x 19 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 19 x 5 mmpack of...

Reference: 117/8

Thrust bearing 8 x 15 x 5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 8 x 15 x 5...

Reference: 116/98

Manifold 34 mm

The various exhaust manifolds differ in shape and in the size of the flange, to match different engines' exhaust stubs. The term "exhaust hole spacing" refers to the holes on either side of the exhaust port, measured between hole centres.Please check before you order that you have selected the correct manifold to match your model and engine. Measure again...

Reference: 11/62

Crankshaft nut socket spanner 13 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 13 mm, for Rossi or Webra

Reference: 16/3

Spray can holder

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Reference: 71/7

Bearing 2 x 6 x 2,5 mm

Not available

Reference: 75/1

10 x 26 x 8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 26 x 8 mmpack of...

Reference: 68/2

20 x 32 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 20 x 32 x 7 mmpack of 1