- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
Plain bushes 3 x 8 mm
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Riferimento: 64/19
15 x 24 x 5 mm
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 15 x 24 x 5 mmpack of...
Riferimento: 11/66
Crankshaft nut socket spanner 10 mm
If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 10 mm, for O.S.
Riferimento: 39/2
10 x 22 x 6 mm
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 10 x 22 x 6 mmpack of...
Riferimento: 116/94
Silencer for 116/95
Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm
Riferimento: 38/1
6 x 19 x 6 mm
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 6 x 19 x 6 mmpack of...
Riferimento: 7/37
8 x 16 x 6 mm
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 8 x 16 x 6 mmpack of...
Riferimento: 10/38
Penetrating oil
When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...
Riferimento: 830/42
Exhaust mount 42 mm
For silencer Ord.No. 116/96.Content of the package1 piece
Riferimento: 94/3
Thrust bearing 4 x 10 x 3 mm
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Thrust bearing 4 x 10 x 3...
Riferimento: 16/3
Spray can holder
This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.
Riferimento: 68/51
Swivel bearing 12 x 22 x 10 mm
A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Swivel bearing 12 x 22 x 10 mmpack of 1
Riferimento: 90/9
Assembly tray, 25-part
Appropriate precautions should always be taken every time you start working on your model, and one of them is to prepare a suitable temporary storage area for small and ultra-small components. These assembly trays are sub-divided into small compartments, allowing you to sort components according to the stage of construction, while a second tray is used to...
Riferimento: 55/7
Thrust bearing 12 x 25 x 6 mm
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing12 x 25 x 6 mm3-part