- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
EC 120 turbine exhaust pipe
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Référence: 268/16
Exhaust for XL-C
Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.
Référence: 214/16
Exhaust for Bell 212 Twin Jet
Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.
Référence: 770/16
Exhaust tube for turbine, BK 117
On the BK 117 the forward thrust is eliminated by the scale division of the exhaust tube (enlarging of the cross-section) and exhausting up through the rotor disc.
Référence: 25/9
Heat reflective mat
Between fuselage and exhaust tube a heat-reflecting mat avoids melting of the fibreglass. Even in smaller fuselages where conventional silencer systems are close to the inside surface, the heat reflective mat is useful as a heat shield.Heat reflective matheat rejectingsize approx. 300 x 700 mmmat thickness approx. 3 mm
Référence: 904/16
Exhaust tube for turbine, Hughes
The shape and dimensions of the Hughes fuselages allow for the installation of a three outlet exhaust. The outlets on the left and right hand sides offer the necessary cross-section and greatly reduce the forward thrust. This keeps the scale rear outlet while only discharging a small amount of the total exhaust gas.
Référence: 791/16
Exhaust tube for turbine, Cobra
Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.
Référence: 206/16
Exhaust for UH-1D
This exhaust system is designed for the UH-1D with turbine power system.Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards...
Référence: 930/16
Exhaust gas efflux for Mil Mi-2
right / leftThis exhaust system is designed for the Mil Mi-2 with turbine power system.
Référence: 340/16
Exhaust for Lama
This exhaust system is designed for the Lama with turbine power system.
Référence: 429/16
Exhaust Bell 429
Stainless steel exhaust manufactured specifically for the Bell 429