Inicio
Marcas

Ninguna marca

Los más vendidos
Bulon 3.5 mm - M 2.0 x 5.0 Vista rápida

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Torica de 2.5 x 12 mm, para Elastomer

74/15
Valoración 
Junta tórica 2,5 x 12 mm, para Elastome
4,40 €
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Junta tórica 2,5 x 12 mm, para Elastome
Detalles del producto
74/15
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Torica de 2.5 x 12 mm, para Elastomer

Torica de 2.5 x 12 mm, para Elastomer

Junta tórica 2,5 x 12 mm, para Elastome
Escriba su propia reseña
16 altri prodotti della stessa categoria:
O-ring 1,5 x 11 mm soft Anteprima

Riferimento: 74/11

O-ring 1,5 x 11 mm soft

Recensioni: 0

O-ring 1,5 x 11 mm soft Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prezzo 4,20 €
Più
In vendita su richiesta
Rotor brake, GRP, red Anteprima

Riferimento: 72/3

Rotor brake, GRP, red

Recensioni: 0

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...

Prezzo 8,00 €
Più
In vendita su richiesta
Set leva miscelatore Anteprima

Riferimento: 78/40

Set leva miscelatore

Recensioni: 0

Mixer levers are an essential part of every flybar-controlled rotor head. From the swashplate a pushrod runs to the ballraced mixer arm which is screwed to the blade holder arm. The mixer levers transmit the control movement to the flybar via the double ball-link.Additionial accessories for the use of mixer levers are either two flanged ballraces or two...

Prezzo 26,70 €
Più
In vendita su richiesta
Inertia weights for Ø 5 mm... Anteprima

Riferimento: 79/8

Inertia weights for Ø 5 mm flybar

Recensioni: 0

Inertia weights are small "extra brakes". They increase the gyroscopic stability of the flybar and slow down the rotor head's response. For every beginner we recommend these so the responsiveness of the rotor head is reduced. The rotor head becomes more responsive as the inertia weights are moveded inwards (always place equally!). Inertia weights suitable...

Prezzo 21,50 €
Più
In vendita su richiesta
Anello 3 x 7 mm. duro Anteprima

Riferimento: 74/10

Anello 3 x 7 mm. duro

Recensioni: 0

O-ring 3 x 7 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prezzo 3,90 €
Più
In vendita su richiesta
GRP blade holder, 5 mm ∅ hole Anteprima

Riferimento: 76/16

GRP blade holder, 5 mm ∅ hole

Recensioni: 0

As demands on helicopters continue to rise, so stronger blade holders are required. In this case a 14 mm blade holder is combined with a 5 mm Ø hole for blade retention, i.e. the matching blade holder screws and self-locking nuts are M5 in size.GRP blade holder with long linkage armfor two-blade rotor heads

Prezzo 21,50 €
Più
In vendita su richiesta