Adaptador, Aluminio , 36 mm

Riferimento: 97/9

Screw fitting pushrod connector

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Riferimento: 33/22

Rotor blade support

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Riferimento: 791/28

Wing brace

The wing brace prevents the wings vibrating; it can be installed in the Cobra, depending on model version.

Riferimento: 603/40

Al plate, mechanics bearer Schweizer 300 C

Component part for fuselages, Ord.No. 6030 or 6031.

Riferimento: 3944

Servo mount 120°

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Riferimento: 97/4

Servo linkage set

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Riferimento: 330/10

Protezione capottina per Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Riferimento: 33/28

Rotor blade tie-down

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Riferimento: 13/21

Magnets for speed regulator

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Riferimento: 33/25

Soporte de la del rotor

Riferimento: 3942

Servo packer

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Riferimento: 17/2

Steel guide 6.2 x 10 mm

Content of the package 1 piece

Riferimento: 890/25

Cooling fan support for Schweizer 300 C

Component part for fuselage, Ord.No. 6030 or 6031.

Riferimento: 3936/1

Y-lead

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Riferimento: 74

O-ring 3 x 8 mm hard

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Riferimento: 33/4

Rotor bolsa de cuchillas 4 cuchillas Ø 2500 mm