Marcas

Ninguna marca

Los productos más vendidos

Varilla de 1.2 x 1200 mm, acero

21/20
Valoración 
Pushrod 1,2 x 1200 mm, acero
3,60 €
En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Pushrod 1,2 x 1200 mm, acero
Detalles del producto
21/20
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Varilla de 1.2 x 1200 mm, acero

Varilla de 1.2 x 1200 mm, acero

Pushrod 1,2 x 1200 mm, acero
Escriba su propia reseña
16 autres produits dans la même catégorie :

Référence: 97/4

Servo linkage set

Commentaire(s): 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prix 32,80 €
Détails
En vente sur demande

Référence: 33/28

Rotor blade tie-down

Commentaire(s): 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Prix 22,10 €
Détails
En vente sur demande

Référence: 3944

Servo mount 120°

Commentaire(s): 0

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Prix 14,20 €
Détails
En vente sur demande

Référence: 10/1

Dispenser for UHU plus endfest 300

Commentaire(s): 0

Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.

Prix 69,50 €
Détails
En vente sur demande

Référence: 3935/4

Servo extension lead 700 mm

Commentaire(s): 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prix 8,90 €
Détails
En vente sur demande

Référence: 33/22

Rotor blade support

Commentaire(s): 0

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Prix 13,10 €
Détails
En vente sur demande

Référence: 18/10

PTFE tube for tail drive shaft

Commentaire(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prix 11,50 €
Détails
En vente sur demande

Référence: 97/9

Screw fitting pushrod connector

Commentaire(s): 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Prix 4,40 €
Détails
En vente sur demande

Référence: 13/21

Magnets for speed regulator

Commentaire(s): 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prix 9,50 €
Détails
En vente sur demande