Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Tubo de PVC 3.0 x 2.0 x 980 mm, red

18/1
Valoración 
Tubo de PVC de 3,0 x 2,0 x 980 mm, rojo
3,10 €
En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Tubo de PVC de 3,0 x 2,0 x 980 mm, rojo
Detalles del producto
18/1
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Tubo de PVC 3.0 x 2.0 x 980 mm, red

Tubo de PVC 3.0 x 2.0 x 980 mm, red

Tubo de PVC de 3,0 x 2,0 x 980 mm, rojo
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 3935/4

Servo extension lead 700 mm

Recensioni: 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prezzo 8,90 €
Più
In vendita su richiesta

Riferimento: 8/3

Tail rotor flange

Recensioni: 0

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Prezzo 8,30 €
Più
In vendita su richiesta

Riferimento: 10/1

Dispenser for UHU plus endfest 300

Recensioni: 0

Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.

Prezzo 69,50 €
Più
In vendita su richiesta

Riferimento: 3944

Servo mount 120°

Recensioni: 0

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Prezzo 14,20 €
Più
In vendita su richiesta

Riferimento: 33/28

Rotor blade tie-down

Recensioni: 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Prezzo 22,10 €
Più
In vendita su richiesta

Riferimento: 33/27

Rotor blade tie-down large

Recensioni: 0

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Prezzo 27,00 €
Più
In vendita su richiesta

Riferimento: 33/22

Rotor blade support

Recensioni: 0

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Prezzo 13,10 €
Più
In vendita su richiesta