Referencia: 92/91
Rodamiento con orejuela de 6 x 10 x 3 mm
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Référence: 64/5
Split taper collet 8 mmmaterial: brassfits the glow plug motor clutchA split taper collet has to be assembled so that it fits tightly onto the crankshaft of the engine.If there are problems sliding the split taper collet easily onto the crankshaft, please insert a screwdriver into the slot and try to open it gently. It should now slide onto the shaft...
Référence: 870/64
Toothed belt clutch bell 32-tooth pitch 3M material: aluminium twin ballraced incl. clutch lining fits the glow plug motor clutch
Référence: 872/64
Toothed belt clutch bell22-toothpitch XLmaterial: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch
Référence: 64/2
If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...
Référence: 833/64
Toothed belt clutchincl. flywheel and split taper collet23-toothpitch 3Mmaterial: aluminiumtwin ballracedincl. clutch liningfits the glow plug motorfor engines up to max. 8.5 cc onlyfits the Sky Dragon model
Référence: 64/38
Clutch bell pinion gear24-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch
Référence: 64/3
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 8 x 16 x 5 mmpack of...
Référence: 64/27
Content of the package1 piece
Référence: 64/42
Clutch pinion gearincl. flywheel and split taper collet20-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor
Référence: 64/8
Friction between the flywheel and the clutch bell result in a certain amount of wear of the clutch lining.For installation you slightly grind one of the outer edges. Afterwards you press the liner with that edge in front into the clutch bell. To glue in a new clutch liner you use e.g. UHU plus endfest 300, Ord.No. 10/26 or 10/27.Fits the glow plug motor...
Référence: 64/21
Clutch bell pinion gear22-toothmodule 1material: GRPtwin ballracedincl. clutch liningfits the glow plug motor clutch
Référence: 64/20
Clutch pinion gear incl. flywheel and split taper collet 22-tooth module 1 material: GRP twin ballraced incl. clutch lining fits the glow plug motor
Référence: 64/36
Clutch pinion gearincl. flywheel and split taper collet24-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor
Référence: 64/17
Flywheel for clutchouter diameter: 39.6 mmheight: 10.5 mmfits the glow plug motor clutch
Référence: 870/65
Toothed belt clutch bell30-toothpitch 3Mmaterial: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch