Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Set de espejos para Lama en escala grande

340/40
Valoración 
Set Espejo de modelo a gran escala
59,40 €
Impuestos incluidos
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Set Espejo de modelo a gran escala
Detalles del producto
340/40
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Set de espejos para Lama en escala grande

Set de espejos para Lama en escala grande

Set Espejo de modelo a gran escala
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 330/2

Imitazione turbina

Recensioni: 0

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Prezzo 106,80 €
Più
In vendita su richiesta

Riferimento: 330/10

Protezione capottina per Lama

Recensioni: 0

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Prezzo 50,20 €
Più
In vendita su richiesta

Riferimento: 340/6

Pedana di salita per Lama

Recensioni: 0

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Prezzo 56,80 €
Più
In vendita su richiesta

Riferimento: 30/50

Estintore, lunghezza ca. 70mm

Recensioni: 0

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Prezzo 21,50 €
Più
In vendita su richiesta

Riferimento: 340/13

Finta trasmissione

Recensioni: 0

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Prezzo 133,60 €
Più
In vendita su richiesta

Riferimento: 340/1

Supporti ruota per Lama

Recensioni: 0

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Prezzo 33,50 €
Più
In vendita su richiesta

Riferimento: 134/455

Torch dummy 1:4

Recensioni: 0

dimensions: diameter: 1.1 cm, length: 5.7 cm

Prezzo 16,50 €
Più
In vendita su richiesta