Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Kit de consola de mando para Lama t 1:4

341/429
Valoración 
Consola de Lama cabina kit 01:04
94,90 €
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Consola de Lama cabina kit 01:04
Detalles del producto
341/429
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Kit de consola de mando para Lama t 1:4

Kit de consola de mando para Lama t 1:4

Consola de Lama cabina kit 01:04
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 340/6

Pedana di salita per Lama

Recensioni: 0

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Prezzo 56,80 €
Più
In vendita su richiesta

Riferimento: 340/13

Finta trasmissione

Recensioni: 0

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Prezzo 133,60 €
Più
In vendita su richiesta

Riferimento: 340/2

Accessori per Lama turbina

Recensioni: 0

The suckering ducts are on the model exactly on the same place as the original ones in position to the turbine on the full-size helicopter.

Prezzo 138,00 €
Più
In vendita su richiesta

Riferimento: 350/17

Coperchio scarico Ø 90 mm

Recensioni: 0

When the turbine of a full-size helicopter is not running, the engine is protected with an exhaust cover which prevents foreign objects finding their way inside the turbine. This exhaust cover for model turbines is suitable for the Lama, Alouette III and any other machine with a 90 mm Ø exhaust pipe. Caution: it is essential to allow the exhaust pipes to...

Prezzo 35,90 €
Più
In vendita su richiesta

Riferimento: 341/509

BTP Lama 1:5

Recensioni: 0

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Prezzo 405,70 €
Più
In vendita su richiesta

Riferimento: 134/444

Connessioni verricello, 1:4

Recensioni: 0

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Prezzo 16,30 €
Più
In vendita su richiesta

Riferimento: 330/2

Imitazione turbina

Recensioni: 0

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Prezzo 106,80 €
Più
In vendita su richiesta

Riferimento: 330/5

Set accessori portelli per Bell 47 G III, Lama

Recensioni: 0

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Prezzo 34,20 €
Più
In vendita su richiesta