Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Entrada de aire turbina 1:4

341/412
Valoración 
Turbina de aire de entrada 01:04
61,30 €
Impuestos incluidos
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Turbina de aire de entrada 01:04
Detalles del producto
341/412
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Entrada de aire turbina 1:4

Entrada de aire turbina 1:4

Turbina de aire de entrada 01:04
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 134/444

Connessioni verricello, 1:4

Recensioni: 0

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Prezzo 16,30 €
Più
In vendita su richiesta

Riferimento: 330/5

Set accessori portelli per Bell 47 G III, Lama

Recensioni: 0

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Prezzo 34,20 €
Più
In vendita su richiesta

Riferimento: 340/13

Finta trasmissione

Recensioni: 0

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Prezzo 133,60 €
Più
In vendita su richiesta

Riferimento: 341/509

BTP Lama 1:5

Recensioni: 0

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Prezzo 405,70 €
Più
In vendita su richiesta

Riferimento: 340/1

Supporti ruota per Lama

Recensioni: 0

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Prezzo 33,50 €
Più
In vendita su richiesta

Riferimento: 1/21

Helmet for pilot William

Recensioni: 0

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Prezzo 26,30 €
Più
In vendita su richiesta

Riferimento: 330/45

Gancio carico

Recensioni: 0

The hook for the Lama is fully functional. The scale aluminium frame comes with further more accessories, inclusive servo mount.The fuselage already offers the fastening, ready soldered.On your model you mount the hook in the required location, and release dummy loads by activating a servo via your transmitter.

Prezzo 105,70 €
Più
In vendita su richiesta

Riferimento: 31/34

Kit cloche con pedali

Recensioni: 0

Incl. programmatore per il nuovo controller del motore lavorato volo mount tempo, Lipo 12S, 5 Ah, ca. 12 minuti, a seconda del pesodel modello.Per l'uso con la...

Prezzo 25,60 €
Più
In vendita su richiesta

Riferimento: 341/405

Pitot 41:4

Recensioni: 0

dimensions: 5.7 x 1.7 x 2.5 cm

Prezzo 16,30 €
Più
In vendita su richiesta