
Referencia: 92/91
Rodamiento con orejuela de 6 x 10 x 3 mm
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Reference: 64/32
Clutch pinion gearincl. flywheel and split taper collet23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor
Reference: 17/23
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 7 x 14 x 3.5 mmpack of...
Reference: 920/50
Component part for fuselage Agusta, Ord.No. 9020 and 9021.
Reference: 830/42
For silencer Ord.No. 116/96.Content of the package1 piece
Reference: 11/62
If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 13 mm, for Rossi or Webra
Reference: 71/19
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 2.5 x 8 x 2.8 mmpack of...
Reference: 84
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 3 x 10 x 4 mmpack of...
Reference: 10/38
When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...
Reference: 11/22
Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...
Reference: 55/7
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing12 x 25 x 6 mm3-part
Reference: 39/2
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 10 x 22 x 6 mmpack of...
Reference: 94/17
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Thrust bearing 7 x 13 x 4.5...
Reference: 111/30
The kit contains: Ord.No. 11/51 PH0, PH1 Ord.No. 11/52 SW 2,5 / 4,0 Ord.No. 111/31 SW 2,0 / 3,5 Ord.No. 111/32 PH000, PH00 Ord.No. 111/33 PZ0, PZ1
Reference: 68/6
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness