
Referencia: 92/91
Rodamiento con orejuela de 6 x 10 x 3 mm
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Référence: 4302
Contenu du paquet 1 piècemoteur chaud - bougie froide (été) moteur froid - bougie chaude (hiver)
Référence: 55/3
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...
Référence: 55/8
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 12 x 28 x 8 mmpack of...
Référence: 84
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 3 x 10 x 4 mmpack of...
Référence: 715/80
Steel manifold for Mizar with petrol engine34 mm hole spacinge.g. for ZG22 or G230
Référence: 64/0
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 9.5 x 22 x 5.5...
Référence: 64/32
Clutch pinion gearincl. flywheel and split taper collet23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor
Référence: 71/11
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...
Référence: 55/6
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 12 x 21 x 5 mmpack of...
Référence: 920/50
Component part for fuselage Agusta, Ord.No. 9020 and 9021.
Référence: 40/1
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 4 x 9 x 4 mmpack of...
Référence: 64/33
Clutch bell pinion gear23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch
Référence: 11/62
If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 13 mm, for Rossi or Webra
Référence: 71/19
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 2.5 x 8 x 2.8 mmpack of...
Référence: 94/17
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Thrust bearing 7 x 13 x 4.5...