Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Reference: 117/8
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Thrust bearing 8 x 15 x 5...
Reference: 94/6
High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Thrust bearing 6 x 10 x 3...
Reference: 111/30
The kit contains: Ord.No. 11/51 PH0, PH1 Ord.No. 11/52 SW 2,5 / 4,0 Ord.No. 111/31 SW 2,0 / 3,5 Ord.No. 111/32 PH000, PH00 Ord.No. 111/33 PZ0, PZ1
Reference: 90/9
Appropriate precautions should always be taken every time you start working on your model, and one of them is to prepare a suitable temporary storage area for small and ultra-small components. These assembly trays are sub-divided into small compartments, allowing you to sort components according to the stage of construction, while a second tray is used to...
Reference: 92/91
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...
Reference: 7/37
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 8 x 16 x 6 mmpack of...
Reference: 68/6
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness
Reference: 17/24
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 8 x 14 x 4 mmpack of...
Reference: 4309
hot engine - cold plug (Summer) cold engine - hot plug (Winter)
Reference: 11/63
If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 11 mm, for Webra; 6.2 mm thread
Reference: 330/18
Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3
Reference: 11/66
If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 10 mm, for O.S.
Reference: 116/8
The operating temperature of a tuned pipe or of a silencer has a destructive influence on their supports, if no heat resitant material is used when fixing.Silicone hose11 mm I.D.length approx. 300 mm
Reference: 75
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 8 x 16 x 4 mmpack of...
Reference: 55/8
Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. Ballrace 12 x 28 x 8 mmpack of...
