Cabeza rotora a escala de Aloutte II, semimontada

Reference: 1005/60

Rotor head petrol mechanics 10 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Reference: 1005/61

Rotor head petrol mechanics 12 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Reference: 703/32

3-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 702/70

Semi scale rotor head

This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...

Reference: 703/480

Chinook rotorhead

 For use on Ord. No. 4800 only !! Other rotorheads cannot be used on this model.Two rotor heads are required for Ord.No. 4800.

Reference: 1005/52

Rotor head up to 2500 mmOrd.No. 1005/52

Ord.No. 1005/52 is for a Ø 15 mm rotor shaft and Ord.No. 1005/49 for Ø 12 mm rotor shaft

Reference: 1005/47

Bell 47 G rotor head

This rotor head was modelled as closely as possible on the original version installed on the Bell 47 G full-size helicopter. It is an excellent choice for use on the Bell 47 G III model, Ord. No. 4700.The centrifugal weights and springs are dummies, and do not work. The rotor blade swivel limits are also imitations, and have no function.The blade grips...

Reference: 705/30

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 722/72

Rotor head VR-22

The loading of every component of this rotor system is designed to take a multiple of the actual forces. We are looking here at purely safety reserves and under no cirumstances should they be used for experimental purposes.Because of the special requirements of materials used in the rotor head, we expressly recommend that only genuine VARIO spare parts...

Reference: 704/35

4-blade rotor head, 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 704/30

4-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 702/62

Rigid 2 blade rotor head 12 mm

Not available

Reference: 1005/59

Rotorkopf für TurbineOrd.No. 1005/59

Reference: 705/37

5-blade rotor head 12 mm

Not available

Reference: 268/72

3-blade rotor head for 15 mm rotor shaft

3-blade rotor head for 15 mm Ø rotor shaft.

Reference: 722/75

Conversion set for rotor head without flybar

This conversion set was originally developed for the Robinson R22 and Jet Ranger, but since then it has proved to be useful for a number of other large-scale models.Please note that the matching...