Rotor principal SkyFox

Reference: 702/70

Semi scale rotor head

This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...

Reference: 705/32

5-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 705/36

5-blade rotor head 12 mm

Not available

Reference: 705/30

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 268/72

3-blade rotor head for 15 mm rotor shaft

3-blade rotor head for 15 mm Ø rotor shaft.

Reference: 1005/47

Bell 47 G rotor head

This rotor head was modelled as closely as possible on the original version installed on the Bell 47 G full-size helicopter. It is an excellent choice for use on the Bell 47 G III model, Ord. No. 4700.The centrifugal weights and springs are dummies, and do not work. The rotor blade swivel limits are also imitations, and have no function.The blade grips...

Reference: 722/72

Rotor head VR-22

The loading of every component of this rotor system is designed to take a multiple of the actual forces. We are looking here at purely safety reserves and under no cirumstances should they be used for experimental purposes.Because of the special requirements of materials used in the rotor head, we expressly recommend that only genuine VARIO spare parts...

Reference: 702/60

CSS 2-blade-rotor head 10 mm / ø5 mm

CSS stands for Cyclic Speed System at this rotor head because the cyclic control occurs more spontaneous.As, for example, a Jet Ranger or an AIRWOLF requires a true-scale look in the air, a rotor head without a flybar is part of the scale detail for these helicopters. Because of its exact reactions in flight we recommend this CSS rotor head.Only the...

Reference: 705/35

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/59

Rotorkopf für TurbineOrd.No. 1005/59

Reference: 705/37

5-blade rotor head 12 mm

Not available

Reference: 1005/52

Rotor head up to 2500 mmOrd.No. 1005/52

Ord.No. 1005/52 is for a Ø 15 mm rotor shaft and Ord.No. 1005/49 for Ø 12 mm rotor shaft

Reference: 703/32

3-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/43

3-blade rotor head for 12 mm, from 20 kg

The take-off weight of our large Alouette III is relatively high, and we therefore decided to revise the linkage for the XL-C rotor head and the 3-blade rotor head in order to optimise the system...

Reference: 722/75

Conversion set for rotor head without flybar

This conversion set was originally developed for the Robinson R22 and Jet Ranger, but since then it has proved to be useful for a number of other large-scale models.Please note that the matching...