Rotor Principal de 5 palas 10mm, 5mm portapalas

Reference: 702/60

CSS 2-blade-rotor head 10 mm / ø5 mm

CSS stands for Cyclic Speed System at this rotor head because the cyclic control occurs more spontaneous.As, for example, a Jet Ranger or an AIRWOLF requires a true-scale look in the air, a rotor head without a flybar is part of the scale detail for these helicopters. Because of its exact reactions in flight we recommend this CSS rotor head.Only the...

Reference: 722/72

Rotor head VR-22

The loading of every component of this rotor system is designed to take a multiple of the actual forces. We are looking here at purely safety reserves and under no cirumstances should they be used for experimental purposes.Because of the special requirements of materials used in the rotor head, we expressly recommend that only genuine VARIO spare parts...

Reference: 1005/12

Rotor head for Bell 212Ord.No. 1005/12

The basic method of operation of the turbine-powered Bell 212's rotor head is the same as that of the Bell 47 G III rotor head. The main difference is that the components have been modified to match the appearance of the Bell 212, and are therefore of different design. For example, a separate swashplate driver is not required, as it is integrated into the...

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/30

3-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/62

Rotorkopf für Turbinen-MechanikOrd.No. 1005/62

Reference: 1005/60

Rotor head petrol mechanics 10 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Reference: 702/80

Semi scale rotor head SKS

The UH-1D or UH-1B models with an excessive length of the rotor shaft out of the mechanics fly for safety reasons with rotor shafts of 12 mm Ø. The difference between the SKS semi-scale rotor heads on offer is due to the centre hub. This version fits the shaft diameter of 12 mm.We recommend this rotor head for experenced pilots only.The performance of...

Reference: 722/75

Conversion set for rotor head without flybar

This conversion set was originally developed for the Robinson R22 and Jet Ranger, but since then it has proved to be useful for a number of other large-scale models.Please note that the matching...

Reference: 702/75

Semi scale rotor head

With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....

Reference: 703/40

3-blade rotor head for 12 mm, for Lama

Large models require strong, rigid rotor heads which are designed to cope with the demands of a rotor disc of commensurate size, and are built for mounting on a 12 mm Ø rotor shaft. The only...

Reference: 702/62

Rigid 2 blade rotor head 12 mm

Not available

Reference: 706/20

6-Blatt Rotorkopf für Ø 12 mm Welle

Reference: 1005/59

Rotorkopf für TurbineOrd.No. 1005/59

Reference: 705/37

5-blade rotor head 12 mm

Not available

Reference: 702/59

2-Blade-Rigid-Rotor head for 10 mm / ø4 mm

Not available