Rotor Principal de 5 palas ,12mm, 5mm portapalas

Reference: 703/43

3-blade rotor head for 12 mm, from 20 kg

The take-off weight of our large Alouette III is relatively high, and we therefore decided to revise the linkage for the XL-C rotor head and the 3-blade rotor head in order to optimise the system...

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 705/35

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 722/75

Conversion set for rotor head without flybar

This conversion set was originally developed for the Robinson R22 and Jet Ranger, but since then it has proved to be useful for a number of other large-scale models.Please note that the matching...

Reference: 702/62

Rigid 2 blade rotor head 12 mm

Not available

Reference: 1005/60

Rotor head petrol mechanics 10 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Reference: 706/20

6-Blatt Rotorkopf für Ø 12 mm Welle

Reference: 1005/50

Sky Fox rotor head

The Sky Fox rotor head in its original form is robust and very sturdy, so it can achieve good results in all flight positions.The rotor head is supplied with a ball raced pitch compensator and two main shaft collars, their use depends on the length of the rotor shaft.CautionIt is not permissible to use this rotor head on a mechanical system powered by a...

Reference: 702/60

CSS 2-blade-rotor head 10 mm / ø5 mm

CSS stands for Cyclic Speed System at this rotor head because the cyclic control occurs more spontaneous.As, for example, a Jet Ranger or an AIRWOLF requires a true-scale look in the air, a rotor head without a flybar is part of the scale detail for these helicopters. Because of its exact reactions in flight we recommend this CSS rotor head.Only the...

Reference: 702/70

Semi scale rotor head

This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...

Reference: 268/72

3-blade rotor head for 15 mm rotor shaft

3-blade rotor head for 15 mm Ø rotor shaft.

Reference: 703/32

3-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 704/30

4-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/59

Rotorkopf für TurbineOrd.No. 1005/59

Reference: 702/75

Semi scale rotor head

With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....

Reference: 704/37

4-blade rotor head 12 mm

Not available