Accueil
Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Rotor blade tie-down large

33/27
Note 

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.
Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor blade harness is attached to the tail boom and / or the skid tubes; this is a safety measure, but keeps the helicopter ready for flight at short notice.

It makes a good-looking accessory for any model, and looks great when your helicopter is parked in the pits.

  • Rotor blade tie-down
  • pack of 1
  • for max. 110 mm blade chord
37,50 €
TTC
Quantité
En vente sur demande

 

Política de seguridad

 

Política de envío

 

Política de devolución

Description

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.
Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor blade harness is attached to the tail boom and / or the skid tubes; this is a safety measure, but keeps the helicopter ready for flight at short notice.

It makes a good-looking accessory for any model, and looks great when your helicopter is parked in the pits.

  • Rotor blade tie-down
  • pack of 1
  • for max. 110 mm blade chord
Détails du produit
33/27
Avis

Aucun avis n'a été publié pour le moment.

Donnez votre avis

Rotor blade tie-down large

Rotor blade tie-down large

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.
Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor blade harness is attached to the tail boom and / or the skid tubes; this is a safety measure, but keeps the helicopter ready for flight at short notice.

It makes a good-looking accessory for any model, and looks great when your helicopter is parked in the pits.

  • Rotor blade tie-down
  • pack of 1
  • for max. 110 mm blade chord
Donnez votre avis
16 altri prodotti della stessa categoria:
Magnets for speed regulator Anteprima

Riferimento: 13/21

Magnets for speed regulator

Recensioni: 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prezzo 11,70 €
Più
In vendita su richiesta
Servo linkage set Anteprima

Riferimento: 97/4

Servo linkage set

Recensioni: 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prezzo 46,10 €
Più
In vendita su richiesta
Servo mounting set Anteprima

Riferimento: 3941/90

Servo mounting set

Recensioni: 0

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Prezzo 11,70 €
Più
In vendita su richiesta
Servo packer Anteprima

Riferimento: 3942

Servo packer

Recensioni: 0

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Prezzo 9,40 €
Più
In vendita su richiesta
PTFE tube for tail drive shaft Anteprima

Riferimento: 18/10

PTFE tube for tail drive shaft

Recensioni: 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prezzo 12,80 €
Più
In vendita su richiesta
Servo numbers Anteprima

Riferimento: 3948

Servo numbers

Recensioni: 0

Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30

Prezzo 11,20 €
Più
In vendita su richiesta
Servo extension lead 700 mm Anteprima

Riferimento: 3935/4

Servo extension lead 700 mm

Recensioni: 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prezzo 9,70 €
Più
In vendita su richiesta

Suivez-nous sur Facebook

Facebook