Marques

No brand

Référence: 97/4

Servo linkage set

Commentaire(s): 0

When you build your first model helicopter you will find all the linkage components required to connect the servos to the mechanics supplied with the RC set (German radio systems only). When you come to installing servos in other models you can use this servo linkage set which contains all the link balls, screws, nuts and screw-fitting pushrod...

Prix 40,10 €
Détails
En vente sur demande
Toutes les meilleures ventes

Stainless steel tube 8.0 mm, 2-part for Jet Ranger

105/14
Note 

 

  • Stainless steel tube 8.0 mm
  • 2-part (462 mm + 1160 mm)
65,70 €
Quantité
En vente sur demande

 

Política de seguridad

 

Política de envío

 

Política de devolución

Description

 

  • Stainless steel tube 8.0 mm
  • 2-part (462 mm + 1160 mm)
Détails du produit
105/14
Avis

Aucun avis n'a été publié pour le moment.

Donnez votre avis

Stainless steel tube 8.0 mm, 2-part for Jet Ranger

Stainless steel tube 8.0 mm, 2-part for Jet Ranger

 

  • Stainless steel tube 8.0 mm
  • 2-part (462 mm + 1160 mm)
Donnez votre avis
16 other products in the same category:

Reference: 17/13

Articulated joint tail drive system

Review(s): 0

On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support

Price 153.40€
More
On sale upon request

Reference: 17/10

Stainless steel tail drive system

Review(s): 0

When a 2 mm steel drive wire is used between main gearbox and tail gearbox the tail rotor might yaw the heli during acrobatics (e.g. turn), because the wire might "wind up". At this moment a small "wind up" will cause a small change of tail rpm, which requires steering corrections.A so-called "rigid" tail drive system gives a more exact drive to the tail...

Price 75.80€
More
On sale upon request

Reference: 17

Tail rotor shaft 2 mm

Review(s): 0

The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm

Price 6.60€
More
On sale upon request

Reference: 17/14

Stainless steel tail drive system for 20 mm

Review(s): 0

Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...

Price 94.20€
More
On sale upon request

Reference: 17/7

Articulated centre support

Review(s): 0

The use of an articulated centre support in helicopters with extreme high mounted tail booms (e.g. Hughes 500) helps to balance up to 30 mm vertical off-set between mechanics and tail rotor. The centre support is double ballraced and pre-assembled.

Price 75.80€
More
On sale upon request

Reference: 17/20

Stainless steel tail drive system

Review(s): 0

This version of the ballraced tail rotor drive system is designed for installation in full-fuselage models. Power is transmitted by a 6 mm stainless steel drive shaft with a length of 980 mm.This length ensures that the system can be used in virtually all our larger fuselages, provided that the main and tail rotors are fitted with the articulated...

Price 114.50€
More
On sale upon request

Reference: 17/16

Stainless steel tube 6.0 x 0.3 x 950 mm

Review(s): 0

Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm

Price 36.50€
More
On sale upon request