Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 420 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 97-108 su 420 articoli

Filtri attivi

Swashplate guide Anteprima

Riferimento: 52/20

Swashplate guide

Recensioni: 0

The swashplate guide prevents the outer ring of the swashplate rotating; the swashplate pin runs in the slot in this guide. The part is fixed to the dome plate using M 3 socket-head cap screws. The length of the swashplate guide slot allows generous collective pitch travels to be exploited to the full; its position on the rotor shaft can be adjusted to...

Prezzo 14,70 €
Più
In vendita su richiesta
Kevlartank para Queroseno... Anteprima

Riferimento: 26/50

Kevlartank para Queroseno 1.4 l

Recensioni: 0

Aramid is a fibre that is used in motor racing. The tanks have an even surface inside and rough on the outside. These fuel tanks are all pressure tested to make sure that they are 100% leak-proof when they arrive at your workshop. They fit in every fuselage, that would normally use the plastic tank Ord.No. 26/5 for. For example, this Aramid tank is...

Prezzo 349,10 €
Più
In vendita su richiesta
Motor mount drilled for... Anteprima

Riferimento: 59/2

Motor mount drilled for Rossi 11.5 cc

Recensioni: 0

Factory-drilled motor mounts, already drilled and tapped for M 3 or M 4, are available in pairs (left / right). Avoid interchanging the left hand with the right hand one!1 pairfactory-drilled

Prezzo 54,60 €
Più
In vendita su richiesta
Flywheel ø 60 x 16 mm Anteprima

Riferimento: 830/61

Flywheel ø 60 x 16 mm

Recensioni: 0

Flywheel for clutchouter diameter: 60 mmheight: 16 mmfits the petrol motor clutch

Prezzo 62,80 €
Più
In vendita su richiesta
Toothed belt clutch bell... Anteprima

Riferimento: 872/64

Toothed belt clutch bell 22-tooth

Recensioni: 0

Toothed belt clutch bell22-toothpitch XLmaterial: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch

Prezzo 99,90 €
Più
In vendita su richiesta
Shim spacer set Anteprima

Riferimento: 59/20

Shim spacer set

Recensioni: 0

To obtain the optimum clearance between clutch pinion and main gear you can use these shim spacers, which are 0.1 and 0.2 mm thick. Simply loosen the engine retaining screws and place the appropriate shim spacer between engine and engine mount; suits all types of engine.Engine spacer set2 each 0.1 mm and 0.2 mm thick

Prezzo 11,20 €
Più
In vendita su richiesta
Exhaust for Bell 212 Twin Jet Anteprima

Riferimento: 214/16

Exhaust for Bell 212 Twin Jet

Recensioni: 0

Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.

Prezzo 552,50 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook