Filtra per

Disponibilità

Disponibilità

Prezzo

Prezzo

  • 5,00 € - 137,00 €

Categorie

Categorie

Marchi

Nessuna marca

Fornitori

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 75 prodotti.

Visualizzati 13-24 su 75 articoli

Filtri attivi

  • Categorie: Attrezzatura specifica
  • Categorie: Files, Perma Grit
  • Categorie: Filiere e punte

Riferimento: 11/69

Drill set 4-part

Recensioni: 0

Most hardware stores offer a very good range of tools like drills. However, when you need special sizes for our special helicopter application, it is very helpful to have a drill set handy which includes exactly the right diameters.  Typical applications: Drill 1.8 mm Ø for flange-head self-tapping screwsDrill 2.0 mm Ø for M 2.5 threadsDrill 2.5 mm...

Prezzo 19,90 €
Più
In vendita su richiesta

Riferimento: 21/11

Tool case

Recensioni: 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prezzo 19,10 €
Più
In vendita su richiesta

Riferimento: 11/260

Glazing panel shears straight

Recensioni: 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prezzo 32,30 €
Più
In vendita su richiesta

Riferimento: 11/70

Twist drill 1.5 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta

Riferimento: 11/71

Twist drill 2.0 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta

Riferimento: 11/28

Glasspaper file, flat

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 14,80 €
Più
In vendita su richiesta

Riferimento: 11/72

Twist drill 2.5 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta

Riferimento: 29/11

Widia disc cutter

Recensioni: 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prezzo 16,90 €
Più
In vendita su richiesta

Riferimento: 11/34

Rotor blade allen key for M6 socket-head screws

Recensioni: 0

Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M6. The T-handle of this M6 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.

Prezzo 11,70 €
Più
In vendita su richiesta

Seguici su Facebook