Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 156 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 37-48 su 156 articoli

Filtri attivi

Tool case set Anteprima

Riferimento: 11/35

Tool case set

Recensioni: 0

We strongly recommend that when you begin assembling your first helicopter you use the correct combination of tools right from the start. This tool case includes Allen keys for grubscrews from M 3 to M 5, a straight-point screwdriver, a cross-point screwdriver, M 3 and M 4 box spanners and thread-lock fluid. The ball-link driver fits into the small box...

Prezzo 94,20 €
Più
In vendita su richiesta
Thread-lock fluid... Anteprima

Riferimento: 10/23

Thread-lock fluid high-strength, 10 ml

Recensioni: 0

Use thread-lock fluid to prevent screws loosening themselves through vibrations.If you wish to use it on a screw please note the difference between types: medium-strength "blue" can be released again if the correct tool is used. High-strength "green" adheres so firmly that the joint can only be released by applying heat, and with plastic parts this could...

Prezzo 14,80 €
Più
In vendita su richiesta
Swashplate jig Anteprima

Riferimento: 68/17

Swashplate jig

Recensioni: 0

Use this swashplate jig to adjust the pushrods of the X-Treme, X-PERIENCE, XLV and Robinson R22 mechanics.

Prezzo 19,40 €
Più
In vendita su richiesta
Glazing panel shears straight Anteprima

Riferimento: 11/260

Glazing panel shears straight

Recensioni: 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prezzo 32,30 €
Più
In vendita su richiesta
Pushrod calipers Anteprima

Riferimento: 11/85

Pushrod calipers

Recensioni: 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.complete with measuring holders

Prezzo 43,90 €
Più
In vendita su richiesta
Twist drill 1.5 mm Anteprima

Riferimento: 11/70

Twist drill 1.5 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta
Flexible glow plug socket... Anteprima

Riferimento: 11/20

Flexible glow plug socket spanner

Recensioni: 0

Many a glow plug is buried inaccessibly inside the model. This flexible socket spanner can be curved to allow you to reach the plug, and you can keep the spanner curved while you screw the plug in or out. Fits all standard glow plugs.

Prezzo 36,50 €
Più
In vendita su richiesta
Swashplate jig Anteprima

Riferimento: 68/4

Swashplate jig

Recensioni: 0

The pushrods from the swashplate to the rotor head must be set to identical lengths.Just slip the swashplate jig under the swashplate, and the swashplate will automatically be set parallel to the dome plate and at right-angles to the rotor shaft. You can now set up all your linkages with confidence.

Prezzo 19,40 €
Più
In vendita su richiesta
Thread-lock fluid... Anteprima

Riferimento: 24/10

Thread-lock fluid medium-strength, 10 ml

Recensioni: 0

Use thread-lock fluid to prevent screws loosening themselves through vibrations.If you wish to use it on a screw please note the difference between types: medium-strength "blue" can be released again if the correct tool is used. High-strength "green" adheres so firmly that the joint can only be released by applying heat, and with plastic parts this could...

Prezzo 15,00 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook