Home

Filtra per

Disponibilità

Disponibilità

Prezzo

Prezzo

  • 5,00 € - 137,00 €

Categorie

Categorie

Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Ci sono 54 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 37-48 su 54 articoli

Filtri attivi

  • Disponibilità: In magazzino
  • Categorie: Attrezzatura specifica
  • Categorie: Files, Perma Grit
  • Categorie: Pinze e cutters
Pipe bending tool Anteprima

Riferimento: 11/80

Pipe bending tool

Recensioni: 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Prezzo 44,30 €
Più
In vendita su richiesta
Pushrod measuring holder Anteprima

Riferimento: 11/86

Pushrod measuring holder

Recensioni: 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prezzo 14,80 €
Più
In vendita su richiesta
Three-armed gripper Anteprima

Riferimento: 9/11

Three-armed gripper

Recensioni: 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Prezzo 11,70 €
Più
In vendita su richiesta
Die M 2.5 HSS Anteprima

Riferimento: 70/20

Die M 2.5 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 46,10 €
Più
In vendita su richiesta
Die M 2.0 HSS Anteprima

Riferimento: 70/21

Die M 2.0 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 54,60 €
Più
In vendita su richiesta
Die M 3.0 HSS Anteprima

Riferimento: 70/22

Die M 3.0 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 37,80 €
Più
In vendita su richiesta
Protective goggles Anteprima

Riferimento: 9/5

Protective goggles

Recensioni: 0

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Prezzo 14,80 €
Più
In vendita su richiesta
File set with handle, six-part Anteprima

Riferimento: 90/10

File set with handle, six-part

Recensioni: 0

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Prezzo 17,00 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook