Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite
Attrezzi / Colle / Lubrificanti

Attrezzi / Colle / Lubrificanti

Attrezzi / Colle / Lubrificanti

Ci sono 26 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 1-12 su 26 articoli

Filtri attivi

  • Categorie: Filiere e punte
  • Categorie: Pinze e cutters
Circlip pliers Anteprima

Riferimento: 11/27

Circlip pliers

Recensioni: 0

Installing and removing the circlip on the main rotor shaft, these circlip pliers do the job and will not damage the circlip. The prongs of the pliers fit exactly in the holes in the circlip and open it evenly, without over-stressing it, so that it can safely be re-used. If you use other tools such as screwdrivers etc. the circlip is easily damaged or...

Prezzo 36,50 €
Più
In vendita su richiesta
Wire cutters for steel wire Anteprima

Riferimento: 11/31

Wire cutters for steel wire

Recensioni: 0

The 2 mm pushrod from the tail rotor servo to the tail rotor bellcrank is made of hardened steel, as is the 2 mm tail rotor shaft. If you need to cut this material to length you need wire cutters which cut cleanly. These wire cutters are the ideal tool for cutting hardened steel wire. Wear protective goggles!

Prezzo 54,60 €
Più
In vendita su richiesta
Hole-cutter, 3 to 14 mm... Anteprima

Riferimento: 11/43

Hole-cutter, 3 to 14 mm diameter, with handle

Recensioni: 0

The pointed tip and the extremely sharp, double-edged blade of this tool are particularly good for cutting holes in thin materials such as GRP and other plastics. The hole-cutter requires no centre-punching and no pilot-hole, and produces a neat hole of infinitely variable diameter within the range 3 to 14 mm. The handle doubles as protection and storage...

Prezzo 43,90 €
Più
In vendita su richiesta
Tap M 5.0 HSS Anteprima

Riferimento: 11/55

Tap M 5.0 HSS

Recensioni: 0

Good thread-cutting oil is as important as the tap, as it extends the useful life of the tool several times over.

Prezzo 19,90 €
Più
In vendita su richiesta
All-purpose pliers Anteprima

Riferimento: 11/37

All-purpose pliers

Recensioni: 0

With these practical, small general purpose pliers you can reach almost all your mechanical parts. These pliers rest nicely in your hand because of the non-slip grips. Overall length 12 cm

Prezzo 12,80 €
Più
In vendita su richiesta
Twist drill 6.0 mm Anteprima

Riferimento: 11/68

Twist drill 6.0 mm

Recensioni: 0

We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta
Ball-link pliers Anteprima

Riferimento: 11/99

Ball-link pliers

Recensioni: 0

When you are carrying out maintenance work on your mechanics or adjusting the mechanical linkages, e.g. to reset blade tracking, you have to push the ball-links off their pivot balls.These special ball-link pliers help you carry out this little task easily and without damaging the links. It is made of high-quality steel, and can be used both to disconnect...

Prezzo 54,60 €
Più
In vendita su richiesta
Drill set 4-part Anteprima

Riferimento: 11/69

Drill set 4-part

Recensioni: 0

Most hardware stores offer a very good range of tools like drills. However, when you need special sizes for our special helicopter application, it is very helpful to have a drill set handy which includes exactly the right diameters.  Typical applications: Drill 1.8 mm Ø for flange-head self-tapping screwsDrill 2.0 mm Ø for M 2.5 threadsDrill 2.5 mm...

Prezzo 19,90 €
Più
In vendita su richiesta
Twist drill 1.5 mm Anteprima

Riferimento: 11/70

Twist drill 1.5 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta
Twist drill 2.0 mm Anteprima

Riferimento: 11/71

Twist drill 2.0 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta
Twist drill 2.5 mm Anteprima

Riferimento: 11/72

Twist drill 2.5 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta
Twist drill 2.8 mm Anteprima

Riferimento: 11/73

Twist drill 2.8 mm

Recensioni: 0

When screwing together parts in the mechanics (direct linkage) Allen screws are preferable to normal screws; use M 2.5 for Futaba servos and M 3 for Graupner / JR servos. We supply all required sizes of drills and taps for the work on your model helicopter.

Prezzo 5,50 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook