Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite

PTFE tube for tail drive shaft

18/10
Valutazione 


PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12)
Length: approx. 740 mm

12,80 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione


PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12)
Length: approx. 740 mm

Dettagli del prodotto
18/10
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

PTFE tube for tail drive shaft

PTFE tube for tail drive shaft


PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12)
Length: approx. 740 mm

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
O-ring 3 x 8 mm hard Anteprima

Riferimento: 74

O-ring 3 x 8 mm hard

Recensioni: 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prezzo 5,40 €
Più
In vendita su richiesta
Wing brace Anteprima

Riferimento: 791/28

Wing brace

Recensioni: 0

The wing brace prevents the wings vibrating; it can be installed in the Cobra, depending on model version.

Prezzo 62,80 €
Più
In vendita su richiesta
Magnets for speed regulator Anteprima

Riferimento: 13/21

Magnets for speed regulator

Recensioni: 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prezzo 11,70 €
Più
In vendita su richiesta
Servo extension lead 700 mm Anteprima

Riferimento: 3935/4

Servo extension lead 700 mm

Recensioni: 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Prezzo 9,70 €
Più
In vendita su richiesta
Tail rotor flange Anteprima

Riferimento: 8/3

Tail rotor flange

Recensioni: 0

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Prezzo 9,70 €
Più
In vendita su richiesta
Y-lead Anteprima

Riferimento: 3936/1

Y-lead

Recensioni: 0

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Prezzo 14,80 €
Più
In vendita su richiesta
Dispenser for UHU plus... Anteprima

Riferimento: 10/1

Dispenser for UHU plus endfest 300

Recensioni: 0

Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.

Prezzo 75,80 €
Più
In vendita su richiesta
Glue dispenser Anteprima

Riferimento: 10/75

Glue dispenser

Recensioni: 0

When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.

Prezzo 49,80 €
Più
In vendita su richiesta
GRP bracket Anteprima

Riferimento: 17/4

GRP bracket

Recensioni: 0

 Content of the package1 piece

Prezzo 12,80 €
Più
In vendita su richiesta
Screw fitting pushrod... Anteprima

Riferimento: 97/9

Screw fitting pushrod connector

Recensioni: 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Prezzo 6,30 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook