Handle for socket spanners Ø 4mm

Référence: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Référence: 11/36

Disc cutter set

Disc cutter set pack of 5 normal variation Wear protective goggles!

Référence: 90/10

File set with handle, six-part

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Référence: 11/59

Juego de herramientas de corte (bisturí + regla)

Référence: 111/11

Handle for socket spanners Ø 6mm

Not available

Référence: 107/1

Ball-link driver 5.5

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Référence: 11/86

Pushrod measuring holder

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Référence: 70/20

Die M 2.5 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Référence: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Référence: 107/0

Ball-link driver with handle

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Référence: 64/2

Flywheel puller

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Référence: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Référence: 11/34

Rotor blade allen key for M6 socket-head screws

Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M6. The T-handle of this M6 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.

Référence: 9/11

Three-armed gripper

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Référence: 29/11

Widia disc cutter

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Référence: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines