Dust guard cover 42 mm

Référence: 10/38

Penetrating oil

When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...

Référence: 116/8

Silicone hose

The operating temperature of a tuned pipe or of a silencer has a destructive influence on their supports, if no heat resitant material is used when fixing.Silicone hose11 mm I.D.length approx. 300 mm

Référence: 870/49

Servo frame CFK

Référence: 68/6

17 x 26 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness

Référence: 7/17

6 x 16 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 16 x 5 mmpack of...

Référence: 68/1

Swivel bearing 10 x 19 x 9 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 10 x 19 x 9 mmpack of 1

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Référence: 71/19

2.5 x 8 x 2.8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 2.5 x 8 x 2.8 mmpack of...

Référence: 94/6

Thrust bearing 6 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 6 x 10 x 3...

Référence: 64/19

15 x 24 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 15 x 24 x 5 mmpack of...

Référence: 40

4 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 4 x 13 x 5 mmpack of...

Référence: 90/9

Assembly tray, 25-part

Appropriate precautions should always be taken every time you start working on your model, and one of them is to prepare a suitable temporary storage area for small and ultra-small components. These assembly trays are sub-divided into small compartments, allowing you to sort components according to the stage of construction, while a second tray is used to...

Référence: 11/22

Magnetiser

Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...

Référence: 17/22

6 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 13 x 5 mmpack of...

Référence: 16/3

Spray can holder

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Référence: 94/17

Thrust bearing 7 x 13 x 4.5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...