Pipe bending tool

Référence: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Référence: 107/2

Ball-link driver 4.0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Référence: 90/10

File set with handle, six-part

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Référence: 11/84

Assembly spanner

If you want to extract the flywheel and the split tapper collet from the motor you hold the flywheel with the assembly spanner while you turn in the extractor screw.

Référence: 11/59

Juego de herramientas de corte (bisturí + regla)

Référence: 70/22

Die M 3.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Référence: 11/36

Disc cutter set

Disc cutter set pack of 5 normal variation Wear protective goggles!

Référence: 11/86

Pushrod measuring holder

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Référence: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Référence: 29/11

Widia disc cutter

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Référence: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Référence: 21/11

Tool case

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Référence: 11/64

Hole cutter up to 16 mm Ø

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Référence: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Référence: 11/57

Abrasive tape, 60 cm

 Replacement sanding strip60 cm roll

Référence: 11/260

Glazing panel shears straight

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...