Accueil
Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Pipe bending tool

11/80
Note 



A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

44,30 €
TTC
Quantité
En vente sur demande

 

Política de seguridad

 

Política de envío

 

Política de devolución

Description



A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Détails du produit
11/80
Avis

Aucun avis n'a été publié pour le moment.

Donnez votre avis

Pipe bending tool

Pipe bending tool



A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Donnez votre avis
16 autres produits dans la même catégorie :
Glasspaper file, flat Aperçu rapide

Référence: 11/28

Glasspaper file, flat

Commentaire(s): 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prix 14,80 €
Détails
En vente sur demande
Pushrod measuring holder Aperçu rapide

Référence: 11/86

Pushrod measuring holder

Commentaire(s): 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prix 14,80 €
Détails
En vente sur demande
Glazing panel shears straight Aperçu rapide

Référence: 11/260

Glazing panel shears straight

Commentaire(s): 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prix 32,30 €
Détails
En vente sur demande
Die M 2.5 HSS Aperçu rapide

Référence: 70/20

Die M 2.5 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 46,10 €
Détails
En vente sur demande
Die M 3.0 HSS Aperçu rapide

Référence: 70/22

Die M 3.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 37,80 €
Détails
En vente sur demande
Widia disc cutter Aperçu rapide

Référence: 29/11

Widia disc cutter

Commentaire(s): 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prix 16,90 €
Détails
En vente sur demande
Ridge cutter Aperçu rapide

Référence: 11/53

Ridge cutter

Commentaire(s): 0

Use this small ridge cutter to remove sharp burrs and edges from aluminium and plastics; e.g. remove sharp edges from an aluminium pipe.

Prix 14,80 €
Détails
En vente sur demande
File set with handle, six-part Aperçu rapide

Référence: 90/10

File set with handle, six-part

Commentaire(s): 0

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Prix 17,00 €
Détails
En vente sur demande
Three-armed gripper Aperçu rapide

Référence: 9/11

Three-armed gripper

Commentaire(s): 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Prix 11,70 €
Détails
En vente sur demande
Die M 2.0 HSS Aperçu rapide

Référence: 70/21

Die M 2.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 54,60 €
Détails
En vente sur demande
Glasspaper file, concave /... Aperçu rapide

Référence: 11/56

Glasspaper file, concave / convex

Commentaire(s): 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prix 12,80 €
Détails
En vente sur demande
Tail blade balance shaft Aperçu rapide

Référence: 34/9

Tail blade balance shaft

Commentaire(s): 0

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Prix 17,00 €
Détails
En vente sur demande
Flywheel puller Aperçu rapide

Référence: 64/2

Flywheel puller

Commentaire(s): 0

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Prix 11,20 €
Détails
En vente sur demande

Suivez-nous sur Facebook

Facebook