Hughes 500E 1:6 - Fuselage kit

Reference: 905/17

Hughes name placard sheet

The Hughes emblem is also available separately, together with the Hughes name placard.Hughes name placard sheetblackfactory-trimmed

Reference: 905/20

Skid tube 12 mm

Skid tubes for model helicopters powered by combustion engines are made of aluminium with a wall thickness of 1 mm.Specification 12 mm ØOverall length approx. 520 mmContent of the package 2 pieces

Reference: 905/31

Hughes 500 E side windows

Hughes 500 E side windowssmoked tintnot trimmed

Reference: 905/32

Hughes 500 E canopy, pointed

Hughes 500 E canopy, pointedsmoked tintnot trimmed

Reference: 905/33

Hughes 500 E canopy, round

Hughes 500 E canopy, roundfür Ord.No. 9005, 9006smoked tintnot trimmed

Reference: 3307

Electric Motor set for Benzin mechanics 12S

For the conversion of benzin mechanics to electric

Reference: 3308

Electric Motor set for Benzin mechanics 10S

For the conversion of benzin mechanics to electric

Reference: 3314/6

Electric drive set for SkyFox 1500 mm rotor disc 6S

kit content:electric motor Kontronik Pyro 700-52 Lcontroller Kontronik JIVE 100+ LVmotor mounttoothed belt pulley 58 t. / 33 t.mounting materialKontronik TelMe can only be used with controllers Kontronik 120 JIVE Pro and higher.

Reference: 35/18

Rotor shaft 10 x 214 mm

 Rotor shaftfor multi-blade headhole spacing 35 mm

Reference: 35/39

Rotor shaft 10 x 174 mm

 Rotor shaftfor multi-blade headhole spacing 35 mm

Reference: 26/100

Benzin kit incl. fuel tank 540 ccm

Not available

Reference: 830/68

Fine-mesh petrol and kerosine filter

Chemical analysis used in Formel 1 is able to determine 1 g of impurity within 1 ton of oil. To fulfill your demand on the cleanness of the fuel for your model helicopter you use the fine-mesh petrol filter inside the fuel tubing between the tank and the carburettor. Also suitable for kerosine turbine fuel.

Reference: 830/83

Petrol fuel tubing 1 m

Fuel tubing for petrolapprox. 1 mtransparentFuel tubing inevitably suffers from the effects of ageing. Always replace brittle tubing before it gives problems! 

Reference: 705/30

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 404/22

5-blade-set 1500 mm

Specification5-blade-setlength: 675 mmrotor disc: 1500 mmblade root: 14 mm 2-holeblade chord: 53 mmprofile thickness: 6.8 mmweight: ca. 165 gmaterial: CFRPShark Skin finish: anthracite mattsymmetry: reflex l.h.r.

Reference: 404/32

5-blade-set 1600 mm

Specification5-blade-setlength: 725 mmrotor disc: 1600 mmblade root: 14 mm 2-holeblade chord: 53 mmprofile thickness: 6.8 mmweight: ca. 175 gmaterial: CFRPShark Skin finish: anthracite mattsymmetry: reflex l.h.r.

Reference: 905/11

Stabiliser set Hughes

 Stabiliser set, GRP2-partfor Hughes 500 with a length up to approx. 1 500 mm

Reference: 905/30

Skid landing gear for Hughes

Skid landing gear for Hugheswith rotor disc 1500 - 1600 mmoriginal kit accessoriescomplete as shown

Reference: 1002/21

Petrol mechanics 90:18

Reference: 830/101

Electric Benzin Conversion Kit, 6mm shaft

Benzin-Trainer to electric conversion?..why not! Here is a rather simple way to convert your Benzin Trainer to electric power. Remove the Petrol motor and exhaust and replace it with an electric motor of your choice. The motor mount retrofit set can be used with the most common electric motors. This conversion set can also be used with the Benzin fuselage...

Reference: 1002/15

Electric "Skyfox" mechanics

Including metal internal tooth gear!These are the electric Skyfox mechanics which are used with one of the following conversion sets for the required gear ratio.Mechanics excludes motor, motor mount, and motor gears... see below.Following the trend for electric models, Vario have produced an electric conversion set for the popular Skyfox mechanics. The...

Reference: 116/99

Silencer system

 Silencer systemIntake pipe 60 mmSilencer chamber 270 mmOverall Ø 50 mmManifold: 34 mm hole spacingTail pipe length 105 mmWeight approx. 250 g

Reference: 1022/13

Carburettor intake trumpet

This screw-fitting carburettor intake trumpet is designed to improve the flow of air entering the carburettor. Complete with screws and gasket.

Reference: 4321

Suppressed plug cap for petrol engine G230 / G240

Suppressed plug cap to protect the radio control system from potential interference caused by the ignition system

Reference: 68/15

Swashplate 5-blade

The swashplate disc can be controlled by 4 ball-end bolts at 90° or by 3 ball-end bolts at 120°, whether the linkage is direct to the servos or utilises bellcranks. As standard there are 4 linkage points.In both types the swashplate bolt assumes the additional function of one linkage point. For a 120° linkage the ball-end bolts have to be replaced with...

Reference: 68/20

Swashplate driver 10 mm

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Reference: 707

Rotor cap for Multi blade head

The diameter is 83 mm and the construction height from the screw-on surface to the highest point is 13 mm.It is fastened using an M4 x 14 hexagon socket screw (included).

Reference: 34/30

Tail rotor blades 130 mm

Tail rotor bladesSpecification 8.0 mm blade root8.7 g approx.29 mm blade chord5.0 mm profile thicknesssymmetrical130 mm longbalanced1 pair

Reference: 1/16

Pilot Gerald, 300 mm

Pilot Geraldbody height 300 mm weight approx. 164 ggrey overall

Reference: 1/60

Pilot Sebastian, 300 mm

Pilot Sebastianheight : 300 mm

Reference: 995

RC system accessories incl. 5 servos

If you already own a radio control system and then purchase a second model helicopter, the next step is to consider carefully which electronic components are the best choice for the new model.The combination illustrated here comprises accessories which have proved excellent in practice. RC system accessories, with Futaba BLS 452 servos excluding radio...

Reference: 14/78

Car sticker Hughes 500 E silver

Car stickers show everyone immediately that you are a member of the helicopter scene. These stickers are factory-trimmed, and make it possible to transfer only the finely cut lines onto the base surface you have choosen. The stickers adhere very well, and do not fade.Color: silverSize approx. 80 x 200 mm 

Reference: 70/40-5

Gestänge 2,5 x 40 mmOrd.No. 70/40-5

Reference: 70/60-5

Gestänge 2,5 x 60 mmOrd.No. 70/60-5

Reference: 33/5

Rotorblatttasche 5-Blatt max Ø 2500 mm