Westland Lynx 1:8 - Fuselage kit

Reference: 750/1

Decal sheet Lynx

Stickers with type specific lettering, registration, and warning notices are printed on clear foil. With ruler and scalpel (Ord.No. 11/59) you will obtain a clean cut for individual items out of a...

Reference: 750/30

Glazing set Lynx

 Westland Lynx glazing setclearnot trimmed

Reference: 3314/6

Electric drive set for SkyFox 1500 mm rotor disc 6S

kit content:electric motor Kontronik Pyro 700-52 Lcontroller Kontronik JIVE 100+ LVmotor mounttoothed belt pulley 58 t. / 33 t.mounting materialKontronik TelMe can only be used with controllers Kontronik 120 JIVE Pro and higher.

Reference: 35/18

Rotor shaft 10 x 214 mm

 Rotor shaftfor multi-blade headhole spacing 35 mm

Reference: 704/30

4-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 404/31

4-blade-set 1600 mm

Specification4-blade-setlength: 725 mmrotor disc: 1600 mmblade root: 14 mm 2-holeblade chord: 53 mmprofile thickness: 6.8 mmweight: ca. 175 gmaterial: CFRPShark Skin finish: anthracite mattsymmetry: reflex l.h.r.

Reference: 750/3

Bulkhead set Lynx

Component part for fuselage, Ord.No. 7050.

Reference: 110/6

Tail skid UH-1D and Lynx

Component part for fuselage UH-1D and Lynx, Ord.No. 1100 and Ord.No. 7050.

Reference: 1002/15

Electric "Skyfox" mechanics

Including metal internal tooth gear!These are the electric Skyfox mechanics which are used with one of the following conversion sets for the required gear ratio.Mechanics excludes motor, motor mount, and motor gears... see below.Following the trend for electric models, Vario have produced an electric conversion set for the popular Skyfox mechanics. The...

Reference: 68/20

Swashplate driver 10 mm

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Reference: 34/7

Tail rotor blades 102 mm, grey

Tail rotor blade, rotor disc 276 mm ØSpecification 8.0 mm blade root9.8 g approx.20-28 mm blade chordinj. moulded GRP3.5 mm profile thicknessdouble reflex102 mm longbalanced1 pair

Reference: 101/45

Four-bladed control bridge, 5 mm ∅

Four-bladed control bridge for 5 mm o/p shaft

Reference: 101/90

Four-bladed hub, complete, 5 mm Ø

Four-bladed hub, complete as shown.Tip: always use the recommended tail rotor blades, and install them in opposed pairs.

Reference: 995

RC system accessories incl. 5 servos

If you already own a radio control system and then purchase a second model helicopter, the next step is to consider carefully which electronic components are the best choice for the new model.The combination illustrated here comprises accessories which have proved excellent in practice. RC system accessories, with Futaba BLS 452 servos excluding radio...

Reference: 190

Undercarriage for Lynx

Undercarriage for Lynxoriginal kit accessoriescomplete as shown

Reference: 33/4

Rotor bolsa de cuchillas 4 cuchillas Ø 2500 mm

Reference: 70/60-4

Varilla de empuje 2.5 x 60 mm