Ecureuil AS 350 1:7 - Fuselage kit

Reference: 412/0

Decal sheet AIR-ZERMATT

Stickers with type specific lettering, registration, and warning notices are printed on clear foil. With ruler and scalpel (Ord.No. 11/59) you will obtain a clean cut for individual items out of a...

Reference: 901/21

Skid bar 10 mm

 Content of the package2 pieces

Reference: 901/22

Skid tube 12 mm

Skid tubes for model helicopters powered by combustion engines are made of aluminium with a wall thickness of 1 mm.Specification 12 mm ØOverall length approx. 450 mmContent of the package 2 pieces

Reference: 114

Window sealing strip

Rubber window sealing strip for scale models; also for resuing glazing panels which have turned out too small. The S-section rubber strip is glued on the inside of the GRP window opening flange. The outside part of the strip is opened up with a screwdriver and the glazing panel slid into the channel.Window sealing stripapprox. 2 mTip: The ball-end M 3...

Reference: 901/30

Glazing set Ecureuil

 Ecureuil glazing setclearnot trimmed

Reference: 35/32

Rotor shaft 10 x 214 mm

 Rotor shaftfor multi-blade headhole spacing 35 mm

Reference: 703/30

3-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 404/40

3-blade-set 1680 mm

Specification3-blade-setlength: 765 mmrotor disc: 1680 mmblade root: 14 mm 2-holeblade chord: 53.0 mmprofile thickness: 6.8 mmweight: ca. 185 gmaterial: CFKShark Skin finish: anthracite mattsymmetry: reflex, l.h.r.

Reference: 70/70

Pushrod 2.5 x 70 mm

Ready-made pushrod, threaded M 2.5, approx. 8 mm thread length each end. Content of the package: 1 piece

Reference: 901/51

Door-set R.H., Ecureuil

Component part for fuselage, Ord.No. 9001 or 9002.

Reference: 901/50

Door-set L.H., Ecureuil

Component part for fuselage, Ord.No. 9001 or 9002.

Reference: 901/12

Vertical stabiliser Ecureuil

Vertical stabiliser, GRPfor Ecureuil with a length up to approx. 1 670 mm

Reference: 901/11

Stabiliser set Ecureuil

 Stabiliser set, GRP2-partfor Ecureuil with a length up to approx. 1 700 mm

Reference: 901/20

Skid landing gear for Ecureuil

 Skid landing gear for Ecureuiloriginal kit accessoriescomplete as shown

Reference: 902/3

Bulkhead set, Ecureuil, petrol

Component part for fuselage, Ord.No. 9001.

Reference: 1002/80

Electric mechanics, excl. motor, 10 mm mainshaft

Reference: 68/20

Swashplate driver 10 mm

Where a pitch compensator sits and two pushrods connect to the flybar, this is now a swashplate driver in its place.This is necessary to drive the inner ring of the swashplate in order to always control the blade angle in the same position.Aluminium swashplate driver with 4 ballraces.

Reference: 707

Rotor cap for Multi blade head

The diameter is 83 mm and the construction height from the screw-on surface to the highest point is 13 mm.It is fastened using an M4 x 14 hexagon socket screw (included).

Reference: 34/30

Tail rotor blades 130 mm

Tail rotor bladesSpecification 8.0 mm blade root8.7 g approx.29 mm blade chord5.0 mm profile thicknesssymmetrical130 mm longbalanced1 pair

Reference: 900/611

Air inlet grill squirrel 1:6

dimensions: 2.9 x 2.9 x 0.1 cm

Reference: 900/609

Door handles rear trapdoors x4 1:6

dimensions: 2.3 x 1.5 x 0.,5 cmPack of 4(Non working dummies)

Reference: 900/622

Wipers squirrel x2 1:6

dimensions: 7.5 x 0.7 x 1 cmPack of 2 (each 2-part)

Reference: 900/620

Door handles squirrel x4 1:6

dimensions: 2 x 0.3 x 0.7 cmPack of 4

Reference: 900/603

Pitot tubes squirrel x2 1:6

dimensions: 1.7 x 1.2 x 0.9 cmPack of 2

Reference: 900/621

Kerosen filling trapdoor squirrel 1:6

dimensions: inner diameter: 0.9 cm, outer diameter: 1.5 cm, height: 1 cm

Reference: 900/610

Air inlet grill squirrel 1:6

dimensions: 2.9 x 1.8 x 0.1 cm

Reference: 900/606

Tail antenna squirrel 1:6

dimensions: 3-D part: 3 x 1.5 x 1 cm

Reference: 900/623

Tail strobe squirrel 1:6

dimensions: diameter: 1 cm, length: 3 cm3-part

Reference: 900/694

Hook for squirrel landing gear 1:6

dimensions: inner diameter: 1.2 cm, height: 1.1 cm3 part

Reference: 900/612

Step on landing gear squirrel 1:6

dimensions: 4.4 x 1.96 x 1.3 cm, diameter: 1.3 cm2-part

Reference: 900/614

Front lower step squirrel x2 1:6

dimensions: 5.4 x 1.6 x 1.9 cmPack of 2

Reference: 900/608

Door handles lower trapdoors x16 1:6

dimensions: 1.8 x 1.5 x 0.5 cmPack of 16

Reference: 900/618

Hinges squirrel x4 1:6

dimensions: 1.8 x 1.2 x 0.5 cmPack of 4

Reference: 900/619

Door handles trapdoors squirrel x4 1:6

dimensions: 1.45 x 1.23 x 0.7 cmPack of 4

Reference: 900/617

Steps squirrel x2

dimensions: 2.37 x 2.23 x 1.33 cmPack of 2

Reference: 900/613

Supports Squirrel x2 1:6

dimensions: 9.2 x 2.65 x 0.17 cmPack of 2 (l/2)

Reference: 900/616

Long step right squirrel 1:6

dimensions: setp length: 14.5 cm, inner diameter fixation: 3.6 cm4-part

Reference: 900/615

Front upper step squirrel x2 1:6

dimensions: 5 x 1.4 x 6.5 cmPack of 2 (l/r)

Reference: 1/70

Pilot Joe, 1:7, white long sleeve + jeans

Pilot Joe 240mm Scale 1:7 white long sleeve + jeans   Made in Germany

Reference: 1/79

Pilot Joe 1:7, long sleeve + trousers

Pilot Joe 240 mm Scale 1:7 long sleeve + trousers Made in Germany

Reference: 995

RC system accessories incl. 5 servos

If you already own a radio control system and then purchase a second model helicopter, the next step is to consider carefully which electronic components are the best choice for the new model.The combination illustrated here comprises accessories which have proved excellent in practice. RC system accessories, with Futaba BLS 452 servos excluding radio...

Reference: 5/900

Coffee mug ECUREUIL big

Not available

Reference: 5/901

Coffee mug ECUREUIL small

Not available

Reference: 10/47

Scale Beschriftung

Reference: 70/70-3

Gestänge 2,5 x 70 mmOrd.No. 70/70-3