Hook for Lama

Riferimento: 341/415

Llamada de rescate por radar x2 1: 4

Riferimento: 341/445

Pedales llama x2 1: 4

Riferimento: 340/13

Finta trasmissione

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Riferimento: 340/1

Supporti ruota per Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Riferimento: 341/418

Reinforcements for skis Lama 1:4

Riferimento: 341/402

Filtro, Lama 1:4

dimensions: 4.3 x 2.5 cm, inner diameter: 1.43 cm

Riferimento: 350/45

CESTELLO SOTTOPANCIA PER LAMA

Great fascination is achieved by active working details on scale models, remember e.g. rotary lights and navigation lights.A working winch adds a special attraction on a model helicopter particularly if it is pivoting and fully functional!Especially on a Alouette III you hardly need fantasy, to see instead of the model the full-size helicopter in your...

Riferimento: 134/411

Antena alrededor de 1: 4

Riferimento: 31/34

Kit cloche con pedali

Incl. programmatore per il nuovo controller del motore lavorato volo mount tempo, Lipo 12S, 5 Ah, ca. 12 minuti, a seconda del pesodel modello.Per l'uso con la...

Riferimento: 341/406

Scatola Fusibili Electric Box Lama 1:4

dimensions: 12.6 x 7 x 4.3 cm2-part

Riferimento: 330/2

Imitazione turbina

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Riferimento: 341/429

Pannello Cockpit dettagliato, LAMA

Addition to the Cockpit Ord. No. 340/29 to make it look more realistic

Riferimento: 341/509

BTP Lama 1:5

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Riferimento: 340/5

Snowboards per Lama 1 paio

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Riferimento: 341/419

Tendicinghia pulegge, 6 pz Lama 1/4

1,18 x 3,15 x 0,72 cmPack of 6

Riferimento: 340/6

Pedana di salita per Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1