Cables Pulleys Lama x6 1:4

Reference: 1/21

Helmet for pilot William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Reference: 330/5

Fittings set Bell 47 G III, Lama

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Reference: 340/1

Wheel holder for Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Reference: 341/36

Load basket

Load basket for Lamalength:410 mmwidth:100 mmheight70 mm

Reference: 341/407

Oil tank large Lama 1:4

dimensions: 6.5 x 4.5 x 6.,5 cm2-part

Reference: 341/415

Llamada de rescate por radar x2 1: 4

Reference: 341/507

Oil tank large Lama 1:4

dimensions: 5.15 x 3.62 x 5.1 cm

Reference: 340/40

Mirror set for large-scale models

Mirror set, complete as illustratede.g. for Lama and other large-scale modelsdimensions of the mirrors: approx. 40 x 84 and 14 x 22 mm

Reference: 330/31

Bubble window for Lama

Bubble window for Lama Ord.No. 3300 / 3400 / 3401, Rotor ø 2500 mm

Reference: 330/2

Dummy turbine, GRP

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Reference: 30/50

Fire extinguisher approx. 70 mm long

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Reference: 340/5

Snowboards for Lama

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Reference: 341/417

Large mirror Lama 1:4

dimensions: 4 x 5.4 x 1 cm

Reference: 341/409

BTP Lama 1: 4

Reference: 341/508

Oil tank small Lama 1:4

dimensions: 5.45 x 1.66 x 5.36 cm

Reference: 341/520

Battery housing /Lama

dimensions: 7.76 x 3.4 x 5.3 cm