Oil tank small Lama 1:4

Riferimento: 340/1

Supporti ruota per Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Riferimento: 330/2

Imitazione turbina

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Riferimento: 134/455

Torch dummy 1:4

dimensions: diameter: 1.1 cm, length: 5.7 cm

Riferimento: 341/414

Lama 1: 4 luz anticolisión trasera

Riferimento: 341/421

Rueda de ventilador Lama 1: 4

Riferimento: 134/460

Telephone on board 1:4

dimensions: 1.9 x 1.2 x 6.3 cm

Riferimento: 31/34

Kit cloche con pedali

Incl. programmatore per il nuovo controller del motore lavorato volo mount tempo, Lipo 12S, 5 Ah, ca. 12 minuti, a seconda del pesodel modello.Per l'uso con la...

Riferimento: 341/424

Kick bar llama 2 partes 1: 4

Riferimento: 341/409

BTP Lama 1: 4

Riferimento: 1/21

Helmet for pilot William

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Riferimento: 340/2

Accessori per Lama turbina

The suckering ducts are on the model exactly on the same place as the original ones in position to the turbine on the full-size helicopter.

Riferimento: 341/406

Scatola Fusibili Electric Box Lama 1:4

dimensions: 12.6 x 7 x 4.3 cm2-part

Riferimento: 134/444

Connessioni verricello, 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Riferimento: 30/50

Estintore, lunghezza ca. 70mm

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Riferimento: 350/45

CESTELLO SOTTOPANCIA PER LAMA

Great fascination is achieved by active working details on scale models, remember e.g. rotary lights and navigation lights.A working winch adds a special attraction on a model helicopter particularly if it is pivoting and fully functional!Especially on a Alouette III you hardly need fantasy, to see instead of the model the full-size helicopter in your...

Riferimento: 330/10

Protezione capottina per Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400