Stabiliser set AIRWOLF, Bell 222

Reference: 38/1

6 x 19 x 6 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 19 x 6 mmpack of...

Reference: 71/16

3 x 7 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 7 x 3 mmpack of...

Reference: 55/2

Bearing 8 x 19 x 6 mm

Not available

Reference: 55/7

Thrust bearing 12 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing12 x 25 x 6 mm3-part

Reference: 870/53

Bearing plate, GFK

Not available

Reference: 330/18

Gear support for tail drive

Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3

Reference: 39/2

10 x 22 x 6 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 22 x 6 mmpack of...

Reference: 11/63

Crankshaft nut socket spanner 11 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 11 mm, for Webra; 6.2 mm thread

Reference: 68/3

25 x 37 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear.The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness

Reference: 117/8

Thrust bearing 8 x 15 x 5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 8 x 15 x 5...

Reference: 17/23

7 x 14 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 7 x 14 x 3.5 mmpack of...

Reference: 11/22

Magnetiser

Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...

Reference: 870/49

Servo frame CFK

Reference: 94/6

Thrust bearing 6 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 6 x 10 x 3...

Reference: 71/19

2.5 x 8 x 2.8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 2.5 x 8 x 2.8 mmpack of...

Reference: 64/16

8 x 12 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 12 x 3.5 mmpack of...