The canopy retainer set helps to keep your canopies undamaged for a long period. It absorbs movement, such as abrupt shocks in hard landings, and prevents cracks developing in the canopy.Knurled nuts are used to hold the canopy in place, and they do not intent the canopy when tightened.The components of the canopy retainer system are screwed against...
These ball-end bolts offer an optimal connection between a GRP servo output arm and the pushrod to the mechanics. Underneath the output arm you lock the ball-end bolt with an M 2 hexagon nut. For aluminium output arms you use ball-end bolts Ord.No. 060/7 and thread-lock fluid.
Ball joints, especially on helicopters that are flown actively by 3-D pilots, are subject to very strong forces. Due to necessary large control movements the ball joints can stretch over a period...
Ball joints, especially on helicopters that are flown actively by 3-D pilots, are subject to very strong forces. Due to necessary large control movements the ball joints can stretch over a period of time. Therefore all ball joints of the rotor head control system should be checked after each flying day. You can get additional safety by using our ball joint security set. The slightly domed and straight washers prevent jumping off of stretched ball joints. Very important: If you change mechanical control movement at the rotor head always check the max. and min. pitch as well as the full cyclic movements to make sure there is no binding. To do this properly turn the rotor head by hand without the blades attached. The set contains all washers and balls as well as high tension socket head bolts to secure the two angled pushrods.
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
Ball-links must be flexible but adequately rigid. The threaded part of the rod cuts its own thread in the ball-link, and no further fixing is necessary. Use silicone oil, Order No. 10/37, for maintenance.Pack of 10Connector fits 4.8 mm ��ballsHow do you know when the pushrod meets the end of the socket, and does it becomes screwed to far into the...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
It is advisable to use stronger pushrods and balls with a larger diameter on demand. This combination often is selected by the pilots with airplanes as well.Ball-link for 3.0 mm pushrodpack of 10connector fits 5.5 mm ��balls
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...
Ball joints, especially on helicopters that are flown actively by 3-D pilots, are subject to very strong forces. Due to necessary large control movements the ball joints can stretch over a period...