Soporte de ventilacion para Schweize 300C

Référence: 3942

Servo packer

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Référence: 33/28

Rotor blade tie-down

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Référence: 8/3

Tail rotor flange

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Référence: 33/5

Rotorblatttasche 5-Blatt max Ø 2500 mm

Référence: 33/6

Rotor blade pouch 2x3 blade max Ø 2100 mm

Référence: 3944

Servo mount 120°

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Référence: 97/9

Screw fitting pushrod connector

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Référence: 21

Pushrod 1.5 x 1000 mm, steel

Pushrod 1.5 x 1000 mm, steel

Référence: 21/20

Pushrod 1.2 x 1200 mm, steel

Pushrod 1.2 x 1200 mm, steel

Référence: 3936/1

Y-lead

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Référence: 18/1

PVC tube 3.0 x 2.0 x 980 mm, red

PVC tube 3.0 x 2.0 x 980 mm, red

Référence: 330/10

Housse de protection pour Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Référence: 33/22

Rotor blade support

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Référence: 33/27

Rotor blade tie-down large

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Référence: 3941

Servo plug lead

Servo plug leadplug for JR

Référence: 333/5

Rotor blade pouch 5-blade Ø 2500 mm

bag length: 120 cmmax. blade width: 9.5 cm